Mitsubishi Outlander XL. Manual — part 1078
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect scan
tool P.54Ah-4."
(2)
Turn the ignition switch to the "ON" position.
(3)
Erase the DTC.
(4)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(5)
Check if the DTC B2350 or B2351 is set.
(6)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
DTC B2351 is set.:
Go to Step 2.
DTC B2350 is set.:
Go to Step 3.
No DTC is set.:
The trouble can be an intermittent
malfunction (GROUP 00 - How to Cope with Intermittent
Malfunction P.00-15).
STEP 2. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
Check again if the DTC is set to the ETACS-ECU.
(1)
Replace the wiper/washer switch.
(2)
Turn the ignition switch to the "ON" position.
(3)
Erase the DTC.
(4)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(5)
Check if DTC is set.
(6)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Go to Step 3.
NO:
The procedure is complete.
STEP 3. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
Check again if the DTC is set to the ETACS-ECU.
(1)
Replace the lighting switch.
(2)
Turn the ignition switch to the "ON" position.
(3)
Erase the DTC.
(4)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(5)
Check if DTC is set.
(6)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Go to Step 4.
NO:
The procedure is complete.
STEP 4. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
Check again if the DTC is set to the ETACS-ECU.
(1)
Turn the ignition switch to the "ON" position.
COLUMN SWITCH
54Ah-7
DIAGNOSIS
(2)
Erase the DTC.
(3)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(4)
Check if DTC is set.
(5)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the diagnostic trouble code set?
YES:
Replace the ETACS-ECU.
NO:
The procedure is complete.
REMOVAL AND INSTALLATION
M15410200010USA0000010000
⦆
To remove the driver airbag module, refer to
GROUP 52B - Service Precautions P.52B-28and
Air Bag Module(s) and Clock Spring P.52B-329.
⦆
When the steering wheel sensor is replaced,
always carry out calibration to make ASC-ECU
learn the neutral point. (Refer to GROUP 35C -
On-vehicle Service-Steering Wheel Sensor
Calibration P.35C-192.) <Vehicles with ASC>
ZC6044620000
2
1
3
Removal Steps
·
Steering column cover (Refer to
GROUP 52A - Instrument Panel
Assembly P.52A-2.)
1.
Wiper/washer switch
2.
Lighting switch
·
Steering wheel assembly (Refer to
GROUP 52B - Air Bag Module(s) and
Clock Spring P.52B-329.)
Removal Steps
·
Clock spring (Refer to GROUP 52B -
Air Bag Module(s) and Clock Spring P.
52B-329.)
3.
Column switch body
·
Steering wheel sensor (Refer to
GROUP 35C - Steering wheel
sensor P.35C-198.) <Vehicles with
ASC>
54Ah-8
COLUMN SWITCH
REMOVAL AND INSTALLATION
INSPECTION
WIPER/WASHER SWITCH CONTINUITY CHECK
M15410200013USA0000010000
ZC600262
1
6
8
11
10
9
7
5
4
3
2
0000
Switch position
Tester
connection
Specified
condition
OFF
-
Open circuit
Windshield intermittent
wiper interval adjusting
knob
6 - 3
Operating
the
adjusting
knob
changes
the
resistance.
Rear wiper switch
6 - 4
Continuity exists (2
ohms or less)
Rear washer switch
6 - 5
Continuity exists (2
ohms or less)
Windshield
washer
switch
6 - 7
Continuity exists (2
ohms or less)
Windshield
wiper switch
Hi
6 - 8
Continuity exists (2
ohms or less)
Lo
6 - 9
Continuity exists (2
ohms or less)
Int
6 - 10
Continuity exists (2
ohms or less)
Mist
6 - 11
Continuity exists (2
ohms or less)
COLUMN SWITCH (SWITCH BODY) CONTINUITY
CHECK
M15410200011USA0000010000
1.
Remove the lighting switch and the wiper/washer switch.
2.
Check that the continuity is present for the same terminal
numbers (No. 2-11) of the column switch body connectors
that remain on the steering column.
ZC502009
1
6
8
11
10
9
7
5
4
3
2
At wiper/washer
switch side
At lighting switch side
0000
1
6
8
11
10
9
7
5
4
3
2
Column
switch
body
Tester
connection
Specified
condition
⦆
Lighting
switch
side connector
⦆
Wiper/washer
switch
side
connector
2 - 2
3 - 3
4 - 4
5 - 5
6 - 6
7 - 7
8 - 8
9 - 9
10 - 10
Continuity exists
(2 Ω or less)
COLUMN SWITCH
54Ah-9
INSPECTION
Column
switch
body
Tester
connection
Specified
condition
11 - 11
54Ah-10
COLUMN SWITCH
INSPECTION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст