Mitsubishi Outlander XL. Manual — part 750
STEP 2. Check the engagement of the liftgate latch
and liftgate striker.
Q:Are the liftgate latch and liftgate striker
engaged correctly?
YES:
Then go to Step 3.
NO:
Align the liftgate latch and liftgate
STEP 3. Retest the system.
Q:Does the liftgate lock operate easily?
YES:
The procedure is complete.
NO:
Return to Step 1.
INSPECTION PROCEDURE 2: Uneven Body Clearance
M14204000907USA0000010000
DIAGNOSIS
STEP 1. Check the clearance around the liftgate.
Q:Is the liftgate installed correctly?
YES:
Go to Step 2.
NO:
Adjust clearance around liftgate (Refer
STEP 2. Retest the system.
Q:Is the clearance with the body even?
YES:
The procedure is complete.
NO:
Return to Step 1.
INSPECTION PROCEDURE 3: Uneven Height
M14204000908USA0000010000
DIAGNOSIS
STEP 1. Check the liftgate damper height.
Q:Is the liftgate damper height proper?
YES:
Go to Step 2.
NO:
Adjust the liftgate damper (Refer to P.
STEP 2. Retest the system.
Q:Are the liftgate and body height even?
YES:
The procedure is complete.
NO:
Return to Step 1.
SPECIAL TOOLS
M14204000006USA0000010000
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB990925
MB990925 Bearing and
oil seal installer set
A:
MB990939
Remover bar
MB990925-01
or
General service tool
Adjustment of door striker
LIFTGATE
42Ac-3
LIFTGATE DIAGNOSIS
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
YB9912230000
Do not use
a
b
c
d
MB991223 Harness set
A: MB991219 Test
harness
B: MB991220 LED
harness
C: MB991221 LED
harness adapter
D: MB991222 Probe
General service tools
Measurement
of
terminal
voltage and resistance
A: Connector pin contact
pressure inspection
B: Power circuit inspection
C: Power circuit inspection
D:
Commercial
tester
connection
MB992006
MB992006 Extra fine
probe
-
Measurement
of
terminal
voltage and resistance
ON-VEHICLE SERVICE
LIFTGATE ALIGNMENT
M14204000009USA0000010000
Required Special Tool:
⦆
MB990939: Brass Bar
LIFTGATE UPPER ALIGNMENT
ZC6001030000
Striker
⦆
If the striker is not engaged with the latch properly, adjust by
loosening the striker mounting screws.
⦆
If the clearance between the liftgate and the body is uneven,
loosen the liftgate-side liftgate hinge mounting bolts to adjust
it.
42Ac-4
LIFTGATE
ON-VEHICLE SERVICE
ZC6001040000
Liftgate hinge
LIFTGATE LOWER ALIGNMENT
ZC6001050000
MB990939
Striker
Temporary
bolts
ZC6001060000
Liftgate hinge
⦆
If the striker is not engaged with the latch properly, remove the
quarter trim lower (Refer to GROUP 52A, Interior Trim P.
52A-10). Replace the striker mounting screw with an
adequate bolt, and use the special tool MB990939 and a
hammer to tap the bolt head in the desired direction to adjust
the striker.
⦆
If the clearance between the liftgate and the vehicle body is
uneven, remove the rear bumper assembly (Refer to GROUP
51, Rear Bumper Assembly P.51A-5) and loosen the body-
side liftgate hinge mounting nuts to adjust the liftgate lower so
that the clearance between the liftgate and body becomes
even.
LIFTGATE
42Ac-5
ON-VEHICLE SERVICE
ADJUSTMENT OF LIFTGATE HEIGHT
M14204000035USA0000010000
ZC600107
Section A – A
0000
15 mm
(0.59 in)
A
A
Damper
Rotate the damper by using the arrow mark on the damper as a
guide to adjust the liftgate height. The damper height is altered
by roughly 4 mm (0.16 inch) when the damper is rotated once.
NOTE:
If a rattling noise is heard due to the vibration of
the liftgate when the vehicle is being driven, adjust the
damper height until the damper is seated on the vehicle
body. The damper should be seated on the vehicle body
regardless of a rattling noise.
LIFTGATE
REMOVAL AND INSTALLATION <LIFTGATE UPPER>
M14204000011USA0000010000
Pre-removal operation
⦆
Liftgate spoiler assembly removal (Refer to GROUP 51A,
⦆
Liftgate trim assembly removal (Refer to GROUP 52A,
⦆
Rear wiper motor removal (Refer to GROUP 51B, Rear Wiper
Post-installation operation
⦆
Liftgate alignment (Refer to P.42Ac-4).
⦆
Adjustment of liftgate height (Refer to P.42Ac-6).
⦆
Rear wiper motor installation (Refer to GROUP 51B, Rear
⦆
Liftgate trim assembly installation (Refer to GROUP 52A,
⦆
Liftgate spoiler assembly installation (Refer to GROUP 51A,
42Ac-6
LIFTGATE
ON-VEHICLE SERVICE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст