Mitsubishi Outlander XL. Manual — part 1075
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect the
scan tool (M.U.T.-III) P.54Af-4."
(2)
Turn the ignition switch to the "ON" position.
(3)
Diagnose the CAN bus line.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the CAN bus line found to be normal?
YES:
Go to Step 2.
NO:
Repair the CAN bus line (Refer to GROUP 54D,
STEP 2. Using scan tool MB991958, check for any
diagnostic trouble code.
Check if DTC is set to the KOS-ECU <vehicles with KOS> or
WCM <vehicles with WCM>.
(1)
Turn the ignition switch to the "ON" position.
(2)
Check whether the KOS or WCM related DTC is set.
(3)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES<vehicles with KOS>:
Troubleshoot the KOS (Refer to
YES<vehicles with WCM>:
Troubleshoot the WCM (Refer to
NO:
Go to Step 3.
STEP 3. Using scan tool MB991958, check data list.
Use the ETACS-ECU data list to check the signals related to the
ignition key cylinder illumination light function.
⦆
Turn the ignition switch to the "LOCK" (OFF) position.
⦆
Remove the ignition key from the ignition key cylinder.
⦆
Open the driver's door.
Item No.
Item name
Normal
conditions
Item 228
Dr door unlock
ON
Item 254
IG voltage
0 V
Item 256
Dr door ajar switch
ON
Item 264
Handle lock switch
Key in → Key
out
IGNITION SWITCH
54Ag-11
SYMPTOM PROCEDURES
Q:Does scan tool MB991958 display the items "Dr door
unlock", "Dr door ajar switch", and "Handle lock switch"
as normal condition?
YES<Normal conditions are displayed for all the
items.>:
Go to Step 4.
NO<Normal condition is not displayed for item No.
228.>:
Troubleshoot the ETACS-ECU. Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 4 "ETACS-ECU does not
receive any signal from the front door lock actuator" P.
54Ad-67.
NO<Normal condition is not displayed for item No.
254.>:
Troubleshoot the ETACS-ECU. Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 2 "ETACS-ECU does not
receive any signal from the ignition switch (IG1)" P.
54Ad-62.
NO<Normal condition is not displayed for item No.
256.>:
Troubleshoot the ETACS-ECU. Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 6 "ETACS-ECU does not
receive any signal from the front the front door switch
(RH)" P.54Ad-75.
NO<Normal condition is not displayed for item No.
264.>:
Troubleshoot the ETACS-ECU. Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 3 "ETACS-ECU does not
receive any signal from key reminder switch" P.54Ad-64.
STEP 4. Check key reminder switch connector C-211,
ETACS-ECU connector C-315 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q:Is key reminder switch connector C-211, ETACS-ECU
connector C-315 in good condition?
YES:
Go to Step 5.
NO:
Repair the damaged parts.
STEP 5. Check the Wiring harness between key reminder
switch connector C-211 (terminal No. 3,5) and ETACS-ECU
connector C-315 (terminal No. 13,18).
⦆
Check the input/output line for open circuit.
Q:Is the check result normal?
YES:
Go to Step 6.
NO:
Repair the wiring harness between key reminder switch
connector C-211 and ETACS-ECU connector C-315.
STEP 6. Check of ignition key cylinder illumination light
bulb.
Q:Is the ignition key cylinder illumination light bulb in good
condition?
YES:
Go to Step 7.
NO:
Replace the bulb of the ignition key cylinder
illumination light.
54Ag-12
IGNITION SWITCH
SYMPTOM PROCEDURES
STEP 7. Retest the system.
Q:Does the ignition key cylinder illumination light
illuminate/extinguish in good condition?
YES:
The trouble can be an intermittent malfunction
(Refer to GROUP 00, How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).
NO:
Replace the ETACS-ECU.
ON-VEHICLE SERVICE
CHECK OF IGNITION KEY REMINDER WARNING
FUNCTION (STEERING LOCK REMINDER TONE
ALARM BY KOS)
M15410000010USA0000010000
1.
Driver's door: Release the closed and steering wheel lock, or
turn the ignition key vehicles with WCM or emergency key
vehicles with KOS to the "LOCK" (OFF) position (key
inserted).
2.
Change the driver's door state from closed to open.
3.
Check that the tone alarm sounds normally.
4.
If a malfunction is found, carry out the troubleshooting (Refer
to GROUP 54Ab, Combination Meter - Trouble Symptom
Chart P.54Ab-40).
REMOVAL AND INSTALLATION
M15410000011USA0000010000
To remove the driver airbag module, refer to
GROUP 52B - Service Precautions P.52B-28and
Air Bag Module(s) and Clock Spring P.52B-329.
Pre-removal Operation
⦆
Removal of lower panel and steering column cover (Refer to
GROUP 52A - Instrument Panel Assembly P.52A-2.)
⦆
Removal of clock spring/column switch assembly (Refer to
GROUP 37 - Steering Shaft P.37-23and GROUP 52B - Air Bag
Module(s) and Clock Spring P.52B-329.)
Post-installation Operation
⦆
Installation of clock spring/column switch assembly (Refer to
GROUP 37 - Steering Shaft P.37-23and GROUP 52B - Air Bag
Module(s) and Clock Spring P.52B-329.)
⦆
Installation of lower panel and steering column cover (Refer to
GROUP 52A - Instrument Panel Assembly P.52A-2.)
IGNITION SWITCH
54Ag-13
ON-VEHICLE SERVICE
ZC600982
ZC600408
ZC600409
<Vehicles with KOS>
2
1
3
<Vehicles with WCM>
1
3
5
4
4
AA00
2.0 ± 0.5 N·m
18 ± 4 in-lb
2.0 ± 0.5 N·m
18 ± 4 in-lb
2
Removal Steps
1.
Ignition switch
2.
Key reminder switch
3.
Key ring illumination light
4.
WCM <vehicles with WCM>/receiver
antenna module <vehicles with KOS>
Removal Steps
<<A>>
5.
Steering lock cylinder <vehicles with
WCM>
REMOVAL SERVICE POINT
<<A>> STEERING LOCK CYLINDER REMOVAL <VEHICLES
WITH WCM>
1.
Insert the key into the steering lock cylinder, and turn the
ignition key to the "ACC" position.
54Ag-14
IGNITION SWITCH
REMOVAL AND INSTALLATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст