Mitsubishi Outlander XL. Manual — part 513

REMOVAL SERVICE POINTS

<<A>> SELECTOR LEVER KNOB REMOVAL

ZC6033380000

Selector lever knob

Pull out the selector lever knob to the direction of arrow shown
in the figure.

<<B>> SHIFT INDICATOR PANEL REMOVAL

ZC6027560000

Insert the slotted head screwdriver into the arrow-indicated point
as shown in the figure to pry the claw, and then remove the shift
indicator panel.

INSTALLATION SERVICE POINTS

>>A<< TRANSAXLE CONTROL CABLE (TRANSAXLE SIDE)
INSTALLATION

ZC601773

Adjusting nut

Transaxle control cable

0002

1.

Move the selector lever and manual control lever to the N
position.

2.

Use the adjusting nut to tighten the transaxle control cable to
the specified torque.

Tightening torque: 9.5 ± 3.5 N·m (84 ± 31 in-lb)

>>B<< KEY INTERLOCK CABLE INSTALLATION

Leave the ignition switch in the "LOCK" (OFF) position until
the key interlock cable installation is completed.

AUTOMATIC TRANSAXLE MECHANICAL

23A-167

TRANSAXLE CONTROL

1.

Move the selector lever to the "P" position and turn the ignition
switch to the "LOCK" (OFF) position.

ZC6022240000

Key inter lock cable

A

View A

Spring

Lock

Adjuster case

Adjuster case

Inner cable

Lock guide

Lock guide

Lock cam

Unlock

2.

Install the tip of the key interlock cable to the lock cam of the
selector lever assembly, taking care not to twist the inner
cable.

3.

Install the adjuster case with its lock guide pulled up
(unlocked).

4.

Securely push down the lock guide to lock it.

NOTE:

The lock position of the key interlock cable is

automatically adjusted by a spring.

SHIFT SWITCH ASSEMBLY CONTINUITY CHECK

M12301000389USA0000010000

ZC6022210000

Selector lever assembly

9

3

2

1
5 6 7 8

4

10

Shift

switch

assembly

Selector lever
position

Terminal
number

Select switch

Sport mode

7 - 8

Shift

switch

(UP)

Upshift and hold 7 - 10

Shift

switch

(DOWN)

Downshift and
hold

7 - 9

A/T KEY INTERLOCK AND SHIFT LOCK MECHANISMS

REMOVAL AND INSTALLATION

M12301000317USA0000010001

When removing and installing the transaxle
control cable and shift lock cable unit, be careful
not to hit the SRS-ECU.

Pre-removal operation

｠

Steering column lower cover and side lower panel assembly

removal (Refer to GROUP 52A - Instrument Panel

Assembly P.52A-2.)

Post-installation operation

｠

Steering column lower cover and side lower panel assembly

installation (Refer to GROUP 52A - Instrument Panel

Assembly P.52A-2.)

23A-168

AUTOMATIC TRANSAXLE MECHANICAL

TRANSAXLE CONTROL

｠

Front floor console assembly removal (Refer to GROUP 52A

- Floor Console Assembly P.52A-8.)

｠

Front floor console assembly installation (Refer to GROUP 52A

- Floor Console Assembly P.52A-8.)

｠

Key interlock mechanism check (Refer to P.23A-162.)

｠

Shift lock mechanism check (Refer to P.23A-163.)

｠

Selector lever operation check (Refer to P.23A-162.)

ZC6023590000

1

3

2

Removal steps

>>B<<

1.

Key interlock cable connection
(selector lever side)

<<A>>

>>A<<

2.

Key interlock cable connection
(steering side)

Removal steps

3.

Key interlock cable

REMOVAL SERVICE POINTS

<<A>> KEY INTERLOCK CABLE (STEERING SIDE)
REMOVAL
Turn the ignition switch to the "ACC" position and then pull the
key interlock cable out from the ignition key cylinder.

INSTALLATION SERVICE POINTS

>>A<< KEY INTERLOCK CABLE (STEERING LOCK
CYLINDER SIDE) INSTALLATION
Turn the ignition switch to the "ACC" position and then install the
key interlock cable to the ignition key cylinder.

AUTOMATIC TRANSAXLE MECHANICAL

23A-169

A/T KEY INTERLOCK AND SHIFT LOCK MECHANISMS

>>B<< KEY INTERLOCK CABLE INSTALLATION

Leave the ignition switch in the "LOCK" (OFF) position until
the key interlock cable installation is completed.

1.

Move the selector lever to the P position and turn the ignition
switch to the "LOCK" (OFF) position.

ZC6022240000

Key inter lock cable

A

View A

Spring

Lock

Adjuster case

Adjuster case

Inner cable

Lock guide

Lock guide

Lock cam

Unlock

2.

Install the tip of the key interlock cable to the lock cam of the
selector lever assembly, taking care not to twist the inner
cable.

3.

Install the adjuster case with its lock guide pulled up
(unlocked).

4.

Securely push down the lock guide to lock it.

NOTE:

The lock position of the key interlock cable is

automatically adjusted by a spring.

TRANSAXLE ASSEMBLY

REMOVAL AND INSTALLATION

M12301000057USA0000010001

｠

The fasteners marked with *1should be
temporarily tightened first and then fully
tightened with the engine weight applied on the
vehicle body.

｠

The bolts marked with *2are coated with the
friction coefficient stabilizer. After removing

these bolts, make sure that they are free of
damage, remove any dust and dirt on the
bearing surfaces and the threads, and then
securely tighten to the specified torque.

Pre-removal operation

｠

Engine compartment under cover and side cover removal

(Refer to GROUP 51A - Under Cover P.51A-18.)

｠

Transmission fluid draining (Refer to P.23A-153.)

｠

Air cleaner bracket removal (Refer to GROUP 15 - Air

Cleaner P.15-6.)

｠

Battery and Battery Tray Removal

｠

ECM removal (Refer to GROUP 13Aa - ECM P.13Aa-37.)

｠

Wiper arm · blade assembly and front deck garnish removal

(Refer to GROUP 51B - Windshield Wiper P.51B-49.)

Post-installation operation

｠

Drive shaft installation (Refer to GROUP 26 P.26-17.)

｠

Strut Tower Bar Installation (Refer to GROUP 42Aa - Strut

Tower Bar P.42Aa-11.)

｠

Wiper arm and blade assembly and front deck garnish

installation (Refer to GROUP 51B - Windshield Wiper P.

51B-49.)

｠

Battery and battery tray installation

｠

ECM installation (Refer to GROUP 13Aa - ECM P.13Aa-37.)

｠

Air cleaner assembly installation (Refer to GROUP 15 - Air

Cleaner P.15-6.)

23A-170

AUTOMATIC TRANSAXLE MECHANICAL

TRANSAXLE ASSEMBLY