Mitsubishi Outlander XL. Manual — part 250
DIAGNOSIS
STEP 1. Check the cooling system.
Refer to GROUP14, Engine Cooling Diagnosis P.14-3.
Q:Is the cooling system normal?
YES:
Go to Step 2.
NO:
Repair it. Then Go to Step 2.
STEP 2. Test the OBD-II drive cycle.
(1)
Carry out test drive with the drive cycle pattern. Refer to
Diagnostic Function - OBD-II Drive Cycle - Pattern 10 P.
13Ab-8.
(2)
Check the diagnostic trouble code (DTC).
Q:Is DTC P0128 set?
YES:
Replace the ECM. When the ECM is replaced, register
the ID code. Refer to GROUP 42B, ID Code Registration
Judgment Table <Vehicles with KOS> P.42B-12or GROUP
42C, ID Code Registration Judgment Table <Vehicles with
WCM> P.42C-8.
NO:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points How to Cope
with Intermittent Malfunctions P.00-15.
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-195
DIAGNOSTIC TROUBLE CODE PROCEDURES
DTC P0131: Heated Oxygen Sensor Circuit Low Voltage (bank 1, sensor 1)
M11310100186USA0000010000
ZK602838
1
2
3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
2
1
4
3
0.5 V
AA00
ENGINE
CONTROL
MODULE
RIGHT BANK HEATED
OXYGEN SENSOR (FRONT)
FROM MFI RELAY
TO ECM
1
2
3
4
55
BLA
CK-WHITE
VIOLET
54
RIGHT BANK HEATED OXYGEN SENSOR (FRONT) CIRCUIT
B-10
B-03
MU802665
13Ab-196
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
ZK603590AA00
Right bank heated
oxygen sensor (front)
Front exhaust
pipe RH
B-03 (GR)
Connector: B-03
ZK603591
ECM
B-10 (GR)
Connector: B-10
AA00
CIRCUIT OPERATION
⦆
A voltage corresponding to the oxygen
concentration in the exhaust gas is sent to the ECM
(terminal No. 54) from the output terminal (terminal
No. 4) of the right bank heated oxygen sensor
(front).
⦆
Terminal No. 2 of the right bank heated oxygen
sensor (front) is grounded with ECM (terminal No.
55).
⦆
The ECM applies an offset voltage of 0.5 volt to
terminal No. 2 of the right bank heated oxygen
sensor (front).
TECHNICAL DESCRIPTION
⦆
The right bank heated oxygen sensor (front) detects
the concentration of oxygen in the exhaust gas; it
converts those data to voltage, and inputs the
resulting signals to the ECM.
⦆
When the right bank heated oxygen sensor (front)
begins to deteriorate, the heated oxygen sensor
signal response becomes poor.
⦆
The ECM also checks for an open circuit in the right
bank heated oxygen sensor (front) output voltage.
DESCRIPTIONS OF MONITOR METHODS
Right bank heated oxygen sensor (front) output
voltage is under specified range.
MONITOR EXECUTION
Continuous
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-197
DIAGNOSTIC TROUBLE CODE PROCEDURES
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored in
memory for the item monitored below)
⦆
Heated oxygen sensor heater (front) monitor
Sensor (The sensor below is determined to be
normal)
⦆
Engine coolant temperature sensor
⦆
Intake air temperature sensor
DTC SET CONDITIONS
Logic Flow Chart
End
Malfunction
Yes
Yes
Yes
No
No
No
2secs have passed?
Output voltage
< 0.2V
Monitoring
conditions
Good
Start
ZK603708 AA00
Check Conditions
⦆
Heated oxygen sensor offset voltage is between 0.4
and 0.6 volt.
⦆
Battery positive voltage is between 11 and 16.5
volts.
⦆
Typically 60 seconds have passed since the engine
starting sequence was completed.
Judgement Criterion
⦆
Right bank heated oxygen sensor (front) output
voltage is lower than 0.2 volt.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function - OBD-II Drive Cycle -
Pattern 23 P.13Ab-8.
13Ab-198
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст