Mitsubishi Outlander XL. Manual — part 983
GENERAL INFORMATION
M15410900001USA0000010006
⦆
For exterior lights, the headlight assemblies, front
fog lights <vehicles without discharge headlight>
and daytime running light*have been installed to the
front of the vehicle, the side turn-signal lights to the
sides of the vehicle (to the fender panel), and the
rear combination light assemblies, tail light
assemblies, rear side marker lights, license plate
lights, and high-mounted stop lights to the rear of
the vehicle.
⦆
The headlight assembly bracket can be replaced
separately.
⦆
For interior lights, the front dome light, rear dome
light, luggage compartment light, glove box light,
center console down light, foot light, and ignition key
cylinder illumination lights have been installed.
NOTE:
*: Vehicles for halogen headlight:
Headlight low-beam decrease in lights. Vehicles
without discharge headlight: Light only for
daytime running light.
CONSTRUCTION DIAGRAM
Exterior lights
ZC501806
Headlight
(low-beam)*
Front turn-signal
light
Front side-marker
light
Position light
Side turn-signal light
Headlight
assembly
0000
Headlight
(high-beam)
Front fog light
<vehicles without discharge headlight>
Daytime running light
<vehicles with discharge headlight>
NOTE: *:
<Vehicles for halogen headlight>
Headlight (low-beam) + daytime running light
<Vehicles for discharge headlight>
Headlight (low-beam)
LIGHTING
54Ac-5
GENERAL INFORMATION
ZC501807
Tail / stop
light
Rear turn-signal
light
Tail light assembly
(back-up light)
License plate light
High-mounted stop light
Rear
combination light
assembly
0000
Rear side-marker light
54Ac-6
LIGHTING
GENERAL INFORMATION
Interior lights
ZC5018590001
Tumble unlocking lever
Front dome light
(map and room light)
Rear dome light
Luggage compartment light
Foot light
Center console
down light
Glove box light
Ignition key cylinder
illumination light
SERVICE SPECIFICATIONS
M15410900002USA0000010000
Item
Standard value
Limit
Headlight aiming
[at 7.62 m (25.0 ft)]
Low-beam
Vertical
direction
Horizontal line (H) ± 50.5
mm (± 2.0 inches) (± 0.38
degrees angle)
-
Horizontal
direction
± 126.4 mm (± 5.0 inches)
(± 0.95 degrees angle)
from the axis, which is
266.1 mm (10.5 inches) (2
degrees angle) rightward
from the vertical line (V)
-
LIGHTING
54Ac-7
SERVICE SPECIFICATIONS
Item
Standard value
Limit
Headlight intensity cd (at high-beam)
-
40,000 or more {when a screen
is set 18.3m(60 ft) ahead of the
vehicles}
Fog light aiming (cutoff line direction) [at 7.62
m (25.0 ft)]
The horizontal line 153.0
mm (6.02 inches) (1.15
degrees angle) below the
horizontal line (H)
-
Fog light aiming (vertical direction) [at 7.62 m
(25.0 ft)]
-
Area from 53.2 mm (2.09 inches)
(0.4 degrees angle) above the
cutoff line to 99.8 mm (3.93
inches) (0.75 degrees angle)
below the cutoff line
Fog light aiming (horizontal direction) [at 7.62
m (25.0 ft)]
-
Vertical line (V) ± 599.7 mm (±
23.6 inches) (± 4.5 degrees
angle).
PRECAUTIONS ON HOW TO USE THE HEADLIGHT ASSEMBLY
Be careful with the following items as resin lenses are
used in the headlight assembly.
⦆
Don't illuminate the headlight for three minutes or
more when the headlight is covered with scratch
protector.
⦆
Don't tape the outer lens.
⦆
Don't scratch the outer lens surface with a sharp
edged special tool.
⦆
Use the specified wax remover and rinse the wax
off cleanly.
⦆
Use the specified genuine bulb.
SPECIAL TOOLS
M15410900003USA0000010000
Tool
Tool number and
name
Supersession
Application
MB990784
MB990784
Ornament remover
General service tool
Removal of front fog light bezel
54Ac-8
LIGHTING
SPECIAL TOOLS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст