Mitsubishi Outlander XL. Manual — part 296
DTC SET CONDITIONS
Logic Flow Chart
Start
Yes
Yes
Yes
No
No
No
Continuous
failure for 0.3sec
Malfunction
End
Good
Output voltage <= 0.2V
(main), 0.2V (sub)
Output voltage > =4.8V
ZK603749 AA00
Check Condition
⦆
Ignition switch is "ON" position.
Judgement Criterion
⦆
Throttle position sensor (sub) output voltage should
be 0.2 volt or less for 0.3 second.
OBD-II DRIVE CYCLE PATTERN
None.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
⦆
Throttle position sensor failed.
⦆
Connector damage
⦆
Harness damage
⦆
ECM failed.
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-379
DIAGNOSTIC TROUBLE CODE PROCEDURES
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
⦆
MB991827: USB Cable
⦆
MB991910: Main Harness A
⦆
MB991658: Test Harness
STEP 1. Using scan tool MB991958, check data list item 15:
Throttle Position Sensor (sub).
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Detach the intake air hose at the throttle body.
(4)
Disconnect the connector of the throttle position sensor.
(5)
Use test harness special tool (MB991658) to connect only
terminals No. 3, No. 4, No. 5, and No. 6.
(6)
Set scan tool MB991958 to the data reading mode for item
15, Throttle Position Sensor (sub).
⦆
Output voltage should be 4.0 volts or more when the
throttle valve is fully closed with your finger.
⦆
Output voltage should be 1.0 volt or less when the throttle
valve is fully open with your finger.
(7)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the sensor operating properly?
YES:
tIt can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
NO:
Go to Step 2.
STEP 2. Check harness connector B-08 at the throttle
position sensor and harness connector B-10 at for damage.
Q:Is the harness connector in good condition?
YES:
Go to Step 3.
NO:
Repair it. Refer to GROUP 00E, Harness Connector
Inspection P.00E-2. Then go to Step 8.
STEP 3. Measure the sensor supply voltage at throttle
position sensor harness side connector B-08.
(1)
Disconnect the connector B-08 and measure at the harness
side.
(2)
Turn the ignition switch to the "ON" position.
13Ab-380
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
ZK603218
1
6
5
4 3
2
B-08 harness connector:
component side
AA00
(3)
Measure the voltage between terminal No. 5 and ground
⦆
Voltage should be between 4.9 and 5.1 volts.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the measured voltage between 4.9 and 5.1 volts?
YES:
Go to Step 5.
NO:
Go to Step 4.
STEP 4. Check for open circuit and harness damage and
short circuit to ground between the throttle position sensor
connector B-08 and the ECM connector B-10.
(1)
Disconnect the throttle position sensor connector B-08 and
the ECM connector B-10.
ZK603219
1
6
5
4 3
2
16 15 14 13 12 11 10 9 8 7 6 5 4 3
2
1
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
AA00
B-10 harness
connector:
component side
B-08 harness
connector:
component side
(2)
Measure the resistance between the throttle position sensor
connector B-08 (terminal No. 5) and the ECM connector B-10
(terminal No. 12).
⦆
Should be less than 2 ohms.
ZK603218
1
6
5
4 3
2
B-08 harness connector:
component side
AA00
(3)
Check for the throttle position sensor connector B-08
(terminal No. 5) and ground.
⦆
Not continuity.
Q:Is the harness wire in good condition?
YES:
Replace the ECM. When the ECM is replaced, register
the ID code. Refer to GROUP 42B, ID Code Registration
Judgment Table <Vehicles with KOS> P.42B-12or GROUP
42C, ID Code Registration Judgment Table <Vehicles with
WCM> P.42C-8. Then go to step 8.
NO:
Repair it. Refer to GROUP 00E, Harness Connector
Inspection P.00E-2. Then go to Step 8.
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-381
DIAGNOSTIC TROUBLE CODE PROCEDURES
STEP 5. Check for open circuit and short circuit to ground
and harness damage between the throttle position sensor
connector B-08 and ECM connector B-10.
(1)
Disconnect the throttle position sensor connector B-08 and
the ECM connector B-10.
16 15 14 13 12 11 10 9 8 7 6 5 4 3
2
1
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
ZK603361
1
2
3
4
5
6
AA00
B-08 Harness
connector:
component side
B-10 Harness
connector:
component side
(2)
Measure the resistance between the throttle position sensor
connector B-08 (terminal No. 6) and the ECM connector B-10
(terminal No. 11).
⦆
Should be less than 2 ohms.
ZK603362
1
2
3
4
5
6
AA00
B-08 Harness
connector:
component side
(3)
Check for the throttle position sensor connector B-08
(terminal No. 6) and ground.
⦆
Not continuity.
Q:Is the harness wire in good condition?
YES:
Go to Step 6.
NO:
Repair it. Then go to Step 8.
STEP 6. Using scan tool MB991958, check data list item 15:
Throttle Position Sensor (sub).
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958 to the data link connector.
(2)
Turn the ignition switch to the "ON" position.
(3)
Detach the intake air hose at the throttle body.
(4)
Disconnect the connector of the throttle position sensor.
(5)
Use test harness special tool (MB991658) to connect only
terminals No. 3, No. 4, No. 5, and No. 6.
(6)
Set scan tool MB991958 to the data reading mode for item
15, Throttle Position Sensor (sub).
13Ab-382
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст