Mitsubishi Outlander XL. Manual — part 698

ZC601123

2

0000

1

Removal steps

·

Position the front wheels in a
straight ahead direction.

>>A<<

1. Clock

spring/column

switch

assembly (Refer to GROUP 52B
- SRS Control Unit P.52B-326.)

Removal steps

>>A<<

2. Steering wheel sensor

INSTALLATION SERVICE POINTS

A NEUTRAL POSITIONING OF STEERING WHEEL SENSOR

ZC601124

Mating marks

0000

｠

Always align the center of the clock spring before
installing the steering wheel sensor. Otherwise, the
sensor can be damaged.

｠

If the center of the clock spring is not correctly aligned,
the steering wheel may not be turned fully or the cable
inside the clock spring may be broken, causing the SRS
air bag to be inoperative or operated incorrectly.

1.

Align the mating marks of the clock spring.
Alignment of mating marks

(1)

Turn the clock spring clockwise fully.

(2)

Turn the clock spring counterclockwise approximately
three and 3/4 turns to align the mating marks.

(3)

Install the clock spring to the column switch.

ACTIVE SKID CONTROL SYSTEM (ASC)

35C-199

STEERING WHEEL SENSOR

ZC6011250000

Steering
wheel sensor

: Neutral position mark

For the vehicles front

For vehicles back

Always align three mating marks of the steering wheel
sensor simultaneously as shown in the figure. If these
mating marks are not aligned correctly, the steering wheel
sensor may be damaged.

2.

Align three mating marks of the steering wheel sensor
simultaneously as shown in the figure.
Alignment of mating marks

(1)

Check the window for inspecting the neutral position of the
steering wheel sensor. If the mating marks cannot be seen
from the window, align the mating marks as shown in the
figure.

(2)

Install the steering wheel sensor to the column switch
assembly, maintaining the neutral position correctly.

NOTE:

A new steering wheel sensor has a pin for

preventing the rotation of (fixing) the steering wheel
sensor. After installing the column switch assembly,
remove this pin.

(3)

Install the column switch assembly to the vehicle,
maintaining the neutral position correctly.

35C-200

ACTIVE SKID CONTROL SYSTEM (ASC)

STEERING WHEEL SENSOR

GROUP 36

PARKING BRAKES

CONTENTS

SERVICE SPECIFICATIONS. . ..

36-2

GREASE. . . . . . ..

36-2

PARKING BRAKES DIAGNOSIS. ....

36-2

INTRODUCTION. . . . ....

36-2

TROUBLESHOOTING STRATEGY. ....

36-2

SYMPTOM CHART. . . . ...

36-2

SYMPTOM PROCEDURES. . . ..

36-3

INSPECTION PROCEDURE 1: Insufficient
Parking Brake Function. . .

36-3

INSPECTION PROCEDURE 2: When the
Parking Brake Lever is Pulled, the
Brake Warning Light does not
Illuminate. . . . . .

36-4

INSPECTION PROCEDURE 3: When the
Parking Brake Lever is Released, the
Brake Warning Light does not Turn Off.
. . . . . . . . ..

36-7

SPECIAL TOOL. . . . ...

36-10

ON-VEHICLE SERVICE. . . .

36-11

PARKING BRAKE LEVER STROKE CHECK AND
ADJUSTMENT. . . . . .

36-11

PARKING BRAKE SWITCH CHECK. . . . .

36-12

PARKING BRAKE LINING SEATING
PROCEDURE. . . . . ..

36-12

PARKING BRAKE LEVER. . .

36-12

REMOVAL AND INSTALLATION. ...

36-12

PARKING BRAKE CABLE. . ....

36-13

REMOVAL AND INSTALLATION. ...

36-13

PARKING BRAKE LINING AND DRUM
. . . . . . . ...

36-14

REMOVAL AND INSTALLATION. ...

36-14

BRAKE LINING THICKNESS CHECK
. . . . . . . ...

36-17

BRAKE DRUM INSIDE DIAMETER CHECK
. . . . . . . ...

36-17

36-1

SERVICE SPECIFICATIONS

M13601000034USA0000010000

Item

Standard value

Limit value

Parking brake lever stroke (Control force approximately 200 N)

3 to 5

-

Brake lining thickness mm

2.8

1.0

Brake dram inside diameter mm

190.0

191.0

GREASE

M13601000004USA0000010000

Item

Brand name

Capacity

Backing plate

Chuo Yuka AKB 100

Adequate

Shoe and lining assembly
Adjuster

PARKING BRAKES DIAGNOSIS

INTRODUCTION

M13601000037USA0000010000

If the parking brake is faulty, parking brake effort will
become insufficient. The cause may be a malfunction

of parking brake parts or the parking brake lever being
out of adjustment.

TROUBLESHOOTING STRATEGY

M13601000038USA0000010000

Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find a
parking brakes fault.

1.

Gather Information from the customer.

2.

Verify that the condition described by the customer
exists.

3.

Find the malfunction by following the Symptom
Chart.

4.

Verify malfunction is eliminated.

SYMPTOM CHART

M13601000041USA0000010000

SYMPTOM

INSPECTION
PROCEDURE

REFERENCE PAGE

Brake drag

-

Refer to GROUP 35A, Basic Brake
System Diagnosis - Symptom
Chart P.35A-5.

Insufficient parking brake function

1

P.36-3

When the parking brake lever is pulled, the brake
warning light does not illuminate.

2

P.36-4

When the parking brake lever is released, the brake
warning light does not turn off.

3

P.36-7

36-2

PARKING BRAKES

SERVICE SPECIFICATIONS