Mitsubishi Outlander XL. Manual — part 697

ASC OFF SWITCH

REMOVAL AND INSTALLATION

M13506100107USA0000010000

NOTE:

Refer to GROUP 52A - Instrument Panel

Assembly for the clip location P.52A-7.

ZC6009980000

1

2

3

5

4

Removal steps

1.

Bottom cover assembly (driver side)

2.

Side air outlet

3.

Lower panel assembly

Removal steps

4.

ASC OFF switch connector

5.

ASC OFF switch

INSPECTION

M13506100108USA0000010000

ASC OFF SWITCH CONTINUITY CHECK

ZC6009990000

1.

As shown in the figure, connect the circuit tester to the ASC
OFF switch terminals No. 1 and No. 2 as a single unit.

2.

If continuity is detected when the ASC OFF switch is pressed
and if not detected when the switch is released, the ASC OFF
switch is in good condition.

ACTIVE SKID CONTROL SYSTEM (ASC)

35C-195

ASC OFF SWITCH

HYDRAULIC UNIT

REMOVAL AND INSTALLATION

M13506100110USA0000010000

NOTE:

ASC-ECU is located in the hydraulic unit.

When the hydraulic unit (integrated with ASC-
ECU) is replaced, always carry out the calibration

of the steering wheel sensor and the G and yaw
rate sensor. (Refer to P.35C-191and P.35C-192.)

Pre-removal operation

｠

Strut tower bar removal (Refer to GROUP 42Aa - Strut Tower

Bar P.42Aa-11.)

｠

Brake fluid draining

｠

Intake manifold plenum removal (Refer to GROUP 15 - Intake

Manifold Plenum P.15-7.)

Post-installation operation

｠

Intake manifold plenum installation (Refer to GROUP 15 -

Intake Manifold Plenum P.15-7.)

｠

Brake fluid refilling and air bleeding (Refer to GROUP 35A - On-

vehicle Service, Brake Fluid Level Inspection and Bleeding P.

35A-18.)

｠

Strut tower bar installation (Refer to GROUP 42Aa - Strut Tower

Bar P.42Aa-11.)

｠

Hydraulic unit check (Refer to P.35C-188.)

ZC5019240001

5

1

11

5

10 ± 2 N·m
89 ± 17 in-lb

24 ± 4 N·m
18 ± 3 ft-lb

5

9

12

16 ± 3 N·m
12 ± 2 ft-lb

5

10

13 ± 2 N·m
111 ± 22 in-lb

3

8

4

5

2

6

7

Removal steps

1.

ASC-ECU harness connector

2.

Suction pipe installation bolt

3.

Wheel

speed

sensor

harness

connector connection

4.

Wheel speed sensor harness clip
connection

Removal steps

>>A<<

5.

Brake tube connection

6.

Brake tube and clip connection

7.

Suction pipe, liquid pipe and clip
connection

8.

Hydraulic unit (ASC-ECU) and
hydraulic unit bracket

35C-196

ACTIVE SKID CONTROL SYSTEM (ASC)

HYDRAULIC UNIT

Removal steps

<<A>>

9.

Hydraulic unit (ASC-ECU)

10. Hydraulic unit bracket insulator
11. Hydraulic unit bracket B

Removal steps

12. Hydraulic unit bracket A

REMOVAL SERVICE POINTS

<<A>> HYDRAULIC UNIT (ASC-ECU) REMOVAL

｠

Be careful when removing the hydraulic unit because it is
heavy.

｠

Never loosen the nuts and the bolts because the hydraulic
unit cannot be disassembled.

｠

Do not drop or shock the hydraulic unit.

｠

Do not turn the hydraulic unit upside down or lay down
the unit because the inner air becomes difficult to be bled.

INSTALLATION SERVICE POINTS

>>A<< BRAKE TUBE CONNECTION

ZC601084

ZC6010850000

1

6

5

3

4

2

Install the brake pipe to the hydraulic unit as shown in the figure.

1.

To rear brake (RH) <Marking color: White>

2.

From master cylinder (secondary) <Marking color: Yellow
and white>

3.

To front brake (LH) <Marking color: Red and white>

4.

To front brake (RH) <Marking color: Orange and white>

5.

From master cylinder (primary) <Marking color: Blue and
white>

6.

To rear brake (LH) <Marking color: Pink>

WHEEL SPEED SENSOR

REMOVAL AND INSTALLATION

M13506100112USA0000010000

Refer to GROUP 35B, Wheel Speed Sensor P.
35B-152.

WHEEL AND TIRE INSPECTION

M13506100113USA0000010000

Refer to GROUP 35B, Wheel and Tire Inspection P.
35B-155.

ACTIVE SKID CONTROL SYSTEM (ASC)

35C-197

WHEEL SPEED SENSOR

G AND YAW RATE SENSOR

REMOVAL AND INSTALLATION

M13506100115USA0000010000

｠

Do not drop or shock the G and yaw rate sensor.

｠

When the G and yaw rate sensor is replaced,
always carry out calibration to make ASC-ECU
learn the neutral point. (Refer to P.35C-191.)

Pre-removal and post-installation steps

｠

SRS control unit (SRS-ECU) removal and installation Refer to GROUP 52B - SRS Control Unit (SRS-ECU) P.52B-326.

ZC6010890000

1

2

5.0 ± 1.0 N·m
44 ± 9 in-lb

Removal steps

1. Harness connector

Removal steps

2. G and yaw rate sensor

STEERING WHEEL SENSOR

REMOVAL AND INSTALLATION

M13506100117USA0000010000

｠

Always align the center of the clock spring
before installing the steering wheel sensor.
Otherwise, the sensor can be damaged.

｠

If the center of the clock spring is not correctly
aligned, the steering wheel may not be turned
fully or the cable inside the clock spring may be
broken, causing the SRS air bag to be
inoperative or operated incorrectly.

｠

Before removing the steering wheel/air bag
module assembly, refer to GROUP 52B - Service
Precautions P.52B-28and Air Bag Module
Clock Spring P.52B-329.

｠

When the steering wheel sensor is replaced,
always carry out calibration to make ASC-ECU
learn the neutral point. (Refer to P.35C-192.)

Pre-removal operation

｠

Air bag module assembly and steering wheel assembly

removal (Refer to GROUP 37 - Steering Wheel P.37-20.)

Post-installation operation

｠

Airbag module assembly and steering wheel assembly

installation (Refer to GROUP 37 - Steering Wheel P.37-20.)

｠

Perform steering wheel calibration. (Refer to P.35C-192.)

35C-198

ACTIVE SKID CONTROL SYSTEM (ASC)

STEERING WHEEL SENSOR