Mitsubishi Outlander XL. Manual — part 338
DTC SET CONDITIONS
Logic Flow Chart
ZK603777AA00
Good
Malfunction
Start
End
No
No
No
No
Yes
Yes
Yes
Yes
Continuous
failure for 2secs
Monitoring
conditions
FLS
r
esistance
< = 2
FLS resistance
< = 186
Check Conditions
⦆
Battery positive voltage is between 11 and 16.5
volts.
⦆
2 seconds or more have passed since the engine
staring sequence was completed.
Judgement Criterion
⦆
Fuel level sensor resistance has continued to be
higher than 186 ohms for 2 seconds.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function - OBD-II Drive Cycle -
Pattern 24 P.13Ab-8.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
⦆
Fuel level sensor failed.
⦆
Combination meters assembly failed.
⦆
Connector damage
⦆
Harness damage
⦆
ECM failed.
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: V.C.I.
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-547
DIAGNOSTIC TROUBLE CODE PROCEDURES
⦆
MB991827: USB Cable
⦆
MB991910: Main Harness A
STEP 1. Check fuel gauge.
Q:Is the fuel gauge functioning?
YES:
Go to Step 2.
NO:
Refer to GROUP 54A, Chassis Electrical - Combination
Meters Assembly - Symptom Chart P.54Ab-40.
STEP 2. Check the trouble symptoms.
(1)
Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function - OBD-II Drive Cycle - Pattern 24 P.
13Ab-8.
(2)
Check the diagnostic trouble code (DTC).
Q:Is DTC P0463 set?
YES:
Replace the ECM. When the ECM is replaced, register
the ID code. Refer to GROUP 42B, ID Code Registration
Judgment Table <Vehicles with KOS> P.42B-12or GROUP
42C, ID Code Registration Judgment Table <Vehicles with
WCM> P.42C-8. Then go to Step 3.
NO:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
STEP 3. Test the OBD-II drive cycle.
(1)
Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function - OBD-II Drive Cycle - Pattern 24 P.
13Ab-8.
(2)
Check the diagnostic trouble code (DTC).
Q:Is DTC P0463 set?
YES:
Retry the troubleshooting.
NO:
The inspection is complete.
13Ab-548
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
DTC P0489: EGR Valve (Stepper Motor) Circuit Malfunction (Ground Short)
M11310100373USA0000010000
1
2 3
4
5 6
ZK602865
1
2
3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
1
3
2
4
1
10 111213 14 1516 17 1819 20
2 3 4
5 6 7 8 9
1
3
4
6
31
32
47
48
B-12
(MU802056)
ENGINE CONTROL MODULE
B-10
20A
WHITE
WHITE
WHITE
WHITE
RED
GRA
Y
-BLUE
SKY BLUE
LIGHT GREEN
WHITE
A-33X
MFI
RELAY
RELAY BOX
(ENGINE COMPARTMENT)
4
3
1
2
22
TO ECM
OFF
ON
AA00
EGR VALVE CIRCUIT
EXHAUST GAS
RECIRCULATION
(EGR) VALVE
36
FUSIBLE LINK
4
2
5
A-13
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
13Ab-549
DIAGNOSTIC TROUBLE CODE PROCEDURES
ZK603634
Exhaust gas
recirculation valve
AA00
B-12(GR)
Connector: B-12
ZK603591
ECM
B-10 (GR)
Connector: B-10
AA00
ZK603589
MFI relay
A-33X
Connector: A-33X
AA00
ZK603650AA00
A-13
Connector: A-13
CIRCUIT OPERATION
⦆
The EGR valve power is supplied from the MFI relay
(terminal No. 2).
⦆
The ECM (terminals No. 31, No. 32, No. 47, No. 48)
drives the stepper motor by sequentially turning
"ON" the power transistors in the ECM and
providing ground to the EGR valve (terminal No. 1,
No. 3, No. 4, No. 6).
TECHNICAL DESCRIPTION
The ECM checks whether a short circuit to the ground
or an open circuit exists or not by measuring the EGR
valve (stepper motor) drive circuit voltage when the
current is not flowing through the coils of the EGR
valve (stepper motor).
DESCRIPTIONS OF MONITOR METHODS
When the EGR valve (stepper motor) drive circuit
voltage is under the specified range, it is judged that
a malfunction exists.
MONITOR EXECUTION
Continuous
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored in
memory for the item monitored below)
⦆
Not applicable
Sensor (The sensor below is determined to be
normal)
⦆
Not applicable
13Ab-550
MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>
DIAGNOSTIC TROUBLE CODE PROCEDURES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст