Mitsubishi Outlander XL. Manual — part 740
Terminal
No.
Check items
Check conditions
Normal conditions
19
Output to power window motor
(Rear left side)
-
-
DOOR DIAGNOSIS
INTRODUCTION TO GLASS AND DOOR
DIAGNOSIS
M14203000073USA0000010002
Glass and door faults include water leaks and improper opening
and closing. Causes for these faults can include faults in the
glass, weatherstrip, drain hole or door installation.
GLASS AND DOOR DIAGNOSTIC
TROUBLESHOOTING STRATEGY
M14203000067USA0000010002
Use these steps to plan your diagnostic strategy. If you follow
them carefully, you will be sure that you have exhausted most
of the possible ways to find a glass and door fault.
1.
Gather information from the customer.
2.
Verify that the condition described by the customer exists.
3.
Find the malfunction by following the Symptom Chart.
4.
Verify malfunction is eliminated.
SYMPTOM CHART
M14203000070USA0000010002
SYMPTOM
INSPECTION
PROCEDURE
REFERENCE PAGE
Water leak through door window glass
1
Door window glass malfunction
2
Water leak through door edge
3
Water leak from door center
4
Door hard to open
5
Door does not open or close completely
6
Uneven gap between body
7
Wind noise around door
8
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Water Leak Through Door Window Glass
M14203000078USA0000010000
DIAGNOSIS
DOOR
42Ab-79
DOOR DIAGNOSIS
STEP 1. Check the window glass runchannel.
Q:Is the window glass runchannel in good
condition?
YES:
Go to Step 2.
NO:
Replace the runchannel, then go to Step 4.
STEP 2. Check the door window glass installation.
Q:Is the door window glass installed correctly?
YES:
Go to Step 3.
NO:
Reinstall the door window glass (Refer
to P.42Ab-97). Then go to Step 4.
STEP 3. Check the clearance at the top of the door
window glass.
Q:Is the clearance at the top of the door window
glass correct?
YES:
Go to Step 4.
NO:
Adjust the door window glass (Refer to P.
STEP 4. Retest the system.
Q:Is any water leaking?
YES:
Return to Step 1.
NO:
The procedure is complete.
INSPECTION PROCEDURE 2: Door Window Glass Malfunction
M14203000079USA0000010000
DIAGNOSIS
STEP 1. Check the door window glass installation
condition.
Q:Is the door window installed correctly?
YES:
Go to Step 2.
NO:
Reinstall the door window glass (Refer
to P.42Ab-97). Then go to Step 4.
STEP 2. Check the delta window glass.
Q:Is the delta window glass in good condition?
YES:
Go to Step 3.
NO:
Repair or replace delta window glass, then
go to Step 4.
STEP 3. Inspect the window regulator assembly.
Q:Is the window regulator assembly in good
condition?
YES:
Go to Step 4.
NO:
Repair or replace the window regulator
assembly, then go to Step 4.
STEP 4. Retest the system.
Q:Does the door window operate correctly?
YES:
The procedure is complete.
NO:
Return to Step 1.
INSPECTION PROCEDURE 3: Water Leak Through Door Edge
M14203000080USA0000010000
DIAGNOSIS
STEP 1. Check the weatherstrip.
Q:Is the weatherstrip in good condition?
YES:
Go to Step 2.
NO:
Replace the weatherstrip, then go to Step
3.
STEP 2. Check the door fit (alignment).
Q:Is the door fit (alignment) correct?
YES:
Go to Step 3.
NO:
Adjust the door fit (Refer to P.42Ab-86).
Then go to Step 3.
STEP 3. Retest the system.
Q:Is any water leaking?
YES:
Return to Step 1.
NO:
The procedure is complete.
42Ab-80
DOOR
DOOR DIAGNOSIS
INSPECTION PROCEDURE 4: Water Leak from Door Center
M14203000081USA0000010000
DIAGNOSIS
STEP 1. Check the drain hole.
Q:Is the drain hole clogged?
YES:
Clean the drain hole, then go to Step 3.
NO:
Go to Step 2.
STEP 2. Check the weatherstrip.
Q:Is the weatherstrip in good condition?
YES:
Go to Step 3.
NO:
Repair or replace the weatherstrip, then go
to Step 3.
STEP 3. Retest the system.
Q:Is any water leaking?
YES:
Return to Step 1.
NO:
The procedure is complete.
INSPECTION PROCEDURE 5: Door Hard to Open
M14203000082USA0000010000
DIAGNOSIS
STEP 1. Adjust the latch and striker engagement.
Q:Is the latch and striker engagement adjusted?
YES:
Go to Step 2.
NO:
Adjust the latch and striker (Refer to P.
STEP 2. Check for lock cable and lock rod
damage.
Q:Are the lock cable and the lock rod damaged?
YES:
Repair or replace the lock cable and the
lock rod, then go to Step 4.
NO:
Go to Step 3.
STEP 3. Check the door handle flexibility (amount
of movement of handle required to open door).
Q:Is the door handle flexibility good?
YES:
Go to Step 4.
NO:
Check the door outside handle and inside
handle (Refer to P.42Ab-92and P.42Ab-93).
Then go to Step 4.
STEP 4. Retest the system.
Q:Does the door open easily?
YES:
The procedure is complete.
NO:
Return to Step 1.
INSPECTION PROCEDURE 6: Door does not Open or Close Completely
M14203000083USA0000010000
DIAGNOSIS
STEP 1. Check the door hinge position.
Q:Is the door hinge correct?
YES:
Go to Step 2.
NO:
Adjust the door hinge (Refer to P.
STEP 2. Check the door for damage.
Q:Is the door in good condition?
YES:
Go to Step 3.
NO:
Repair or replace the door, then go to Step
4.
STEP 3. Check lubrication.
Q:Are the door check and door hinge sufficiently
lubricated?
YES:
Go to Step 4.
NO:
Apply grease, then go to Step 4.
STEP 4. Retest the system.
Q:Does the door open and close completely?
DOOR
42Ab-81
DOOR DIAGNOSIS
YES:
The procedure is complete.
NO:
Return to Step 1.
INSPECTION PROCEDURE 7: Uneven Gap Between Body
M14203000084USA0000010000
DIAGNOSIS
Adjust the door fit (Refer to P.42Ab-97). Then check
that the gap has been improved.
INSPECTION PROCEDURE 8: Wind Noise Around Door
M14203000085USA0000010000
DIAGNOSIS
STEP 1. Check the weatherstrip for holding
condition.
Q:Is the weatherstrip holding firmly?
YES:
Go to Step 2.
NO:
Adjust fit of weatherstrip. Then go to Step
5.
STEP 2. Check the weatherstrip for installation
condition.
Q:Is the weatherstrip installed properly?
YES:
Go to Step 3.
NO:
Repair or replace the weatherstrip. Then go
to Step 5.
STEP 3. Check the clearance.
Q:Are the door glass and door weatherstrip holder
installed properly?
YES:
Go to Step 4.
NO:
Adjust the door glass and the weatherstrip
holder (Refer to P.42Ab-88). Then go to Step
5.
STEP 4. Check the door for deformation.
Q:Is the door deformed?
YES:
Replace the door. Then go to Step 5.
NO:
Go to Step 5.
STEP 5. Retest the system.
Q:Has the wind noise been improved?
YES:
Return to Step 1.
NO:
This diagnosis complete.
HOW TO LOCATE WIND NOISE
M14203000983USA0000010000
ZC6001230000
1.
Attach cloth tape to every place, such as panel seams,
projections, molding seams, glass and body seams, etc. which
might conceivably be the source of wind noise.
2.
Then make a road test to check that the places not covered
by tape are not sources of wind noise.
42Ab-82
DOOR
DOOR DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст