Mitsubishi Outlander XL. Manual — part 741
ZC6001230000
3.
Remove the strips of tape one by one, making a road test after
each is removed, until a wind noise source is discovered.
ZC6001240000
4.
When such a place is found, cover it again and repeat the
procedure to check if there are any other noise source.
5.
If no others are found, the last remaining tape is the only
source.
ZC6001250000
6.
Cut the remaining piece of tape into smaller pieces, attach it
again as it was before, and then remove the pieces one by
one to narrow down the source.
ZC6001260000
7.
Check that wind noise occurs when the last remaining tape is
removed, and that noise does not occur when it is re-attached.
8.
When the source(s) of the wind noise is finally located, attach
butyl tape, body sealer or similar material to obstruct this
source as much as possible.
SPECIAL TOOLS
M14203000006USA0000010000
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB990480
MB990480 Glass holder General service tool
Removal and installation of
power window regulator
DOOR
42Ab-83
SPECIAL TOOLS
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB990900
MB990900
or
MB991164
Door
adjusting wrench
MB990900-01
Adjustment of door fit
MB990925
MB990925 Bearing and
oil seal installer set
A:
MB990939
Remover bar
MB990925-01
or
General service tool
Adjustment of door striker
YB990211AA00
MB990211
Slider
hammer
MB990211-01
MB990241
A
AE
MB990241 Axle shaft
puller
A: MB990243 Body
puller
MB990241-01
or
General service tool
42Ab-84
DOOR
SPECIAL TOOLS
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991910
MB991826
MB991911
MB991914
MB991824
MB991827
MB991825
Do not use
A
B
C
D
E
F
G
Do not use
YB9919580001
MB991958
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991914
F: MB991825
G: MB991826
Scan tool (M.U.T.-III sub
assembly)
A:
Vehicle
communication
interface (V.C.I.)
B: M.U.T.-III USB
cable
C: M.U.T.-III main
harness A (Vehicles
with
CAN
communication
system)
D: M.U.T.-III main
harness B (Vehicles
without
CAN
communication
system)
E: M.U.T.-III main
harness C (for Daimler
Chrysler models only)
F:
M.U.T.-III
measurement adapter
G: M.U.T.-III trigger
harness
MB991824-KIT
NOTE:
G: MB991826
M.U.T.-III Trigger
Harness is not
necessary when pushing
V.C.I. ENTER key.
Communication line check
(ECU check and service data)
For vehicles with CAN
communication, use M.U.T.-
III main harness A to send
simulated vehicle speed. If
you connect M.U.T.-III main
harness B instead, the CAN
communication does not
function correctly.
DOOR
42Ab-85
SPECIAL TOOLS
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
YB9912230000
Do not use
a
b
c
d
MB991223 Harness set
A: MB991219 Test
harness
B: MB991220 LED
harness
C: MB991221 LED
harness adapter
D: MB991222 Probe
General service tools
Making voltage and resistance
measurement
during
troubleshooting
A: Connector pin contact
pressure inspection
B: Power circuit inspection
C: Power circuit inspection
D:
Commercial
tester
connection
MB992006
MB992006
Extra fine probe
-
Making voltage and resistance
measurement
during
troubleshooting
ON-VEHICLE SERVICE
FRONT DOOR FIT ADJUSTMENT
M14203000012USA0000010000
Required Special Tools:
⦆
MB990211: Slide Hammer
⦆
MB990243: Body Puller
⦆
MB990900 or MB991164: Door adjusting Wrench
⦆
MB990939: Brass Bar
ZC600064
MB990900
or
MB991164
0000
⦆
Do not rotate special tool MB991164 with a torque of over
98 N?m (72 ft-lb).
1.
When the clearance between the door and the body is uneven
(1)
Apply protective tape to the fender around the hinge
installation position and door edge.
(2)
Remove the splash shield front <Front door only> (Refer
to GROUP 42Aa, Splash Shield P.42Aa-9).
(3)
Remove the center pillar trim <Rear door only> (Refer to
GROUP 52A, Interior Trim P.52A-10).
(4)
Use special tool MB990900 or MB991164 to loosen the
hinge mounting bolts on the body side, and then adjust the
clearance around the door so that it is uniform on all sides.
(5)
Move the door to adjust until the clearance around the door
is even.
42Ab-86
DOOR
ON-VEHICLE SERVICE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст