Mitsubishi Outlander XL. Manual — part 1019
Diagnosis - Inspection Procedure 7 "ETACS-ECU does not
receive any signal from the rear door switch (LH)" P.
54Ad-77.
NO<Normal condition is not displayed for item No.
259.>:
Troubleshoot the ETACS-ECU.Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 8 "ETACS-ECU does not
receive any signal from the rear door switch (RH)" P.
54Ad-80.
NO<Normal condition is not displayed for item No.
260.>:
Troubleshoot the ETACS-ECU.Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 9 "ETACS-ECU does not
receive any signal from the liftgate switch" P.
54Ad-82.
NO<Normal condition is not displayed for item No.
264.>:
Troubleshoot the ETACS-ECU.Refer to GROUP 54Ad,
Diagnosis - Inspection Procedure 3 "ETACS-ECU does not
receive any signal from the key reminder switch" P.
54Ad-64.
STEP 4. Check rear dome light connector D-10 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is rear dome light connector D-10 in good condition?
YES:
Go to Step 5.
NO:
Repair the damaged parts.
STEP 5. Rear dome light bulb check
Check that the rear dome light bulb is normal.
Q:Does rear dome light work normal?
YES:
Go to Step 6.
NO:
Replace the rear dome light bulb.
STEP 6. Check ETACS-ECU connector C-316 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is ETACS-ECU connectors C-311 in good condition?
YES:
Go to Step 7.
NO:
Repair the damaged parts.
STEP 7. Check the wiring harness between rear dome light
D-10 connector terminal (No. 1/2) and ETACS-ECU
connector C-316 (terminal No. 6/5)
Q:Is wiring harness between rear dome light connector D-10
(terminal No. 1/2) and ETACS-ECU connector C-316
(terminal No. 6/5) in good condition?
YES:
Go to Step 8.
NO:
Repair the wiring harness.
STEP 8. Retest the system
Check that the rear dome light illuminates/extinguishes
normally.
Q:Does rear dome light work normal?
LIGHTING
54Ac-149
DIAGNOSIS
YES:
The trouble can be an intermittent malfunction
(Refer to GROUP 00 - How to use Troubleshooting/
inspection Service Points - How to Cope with Intermittent
Malfunction P.00-15).
NO:
Replace the ETACS-ECU.
Inspection Procedure 3: The luggage compartment light does not illuminate normally.
M15410900127USA0000010000
Luggage Compartment Light Circuit
ETACS-ECU
LUGGAGE
COMPARTMENT
LIGHT
ZC6008780025
Connector: C-311
54Ac-150
LIGHTING
DIAGNOSIS
ZC6008820006
Connector: F-02
F-02 (GR)
ZC600880
Connector: D-12
0006
TROUBLE JUDGMENT
The ETACS-ECU illuminates and extinguishes the
luggage compartment light in accordance with the
input signals below.
⦆
Ignition switch (IG1)
⦆
Key reminder switch
⦆
Door switches
⦆
Liftgate latch switch
⦆
Front door lock actuator
TECHNICAL DESCRIPTION (COMMENT)
If this does not work normally, the above switch input
circuit(s), luggage compartment light, or ETACS-ECU
may have a problem.
TROUBLESHOOTING HINTS
⦆
Malfunction of the key reminder switch
⦆
Malfunction of door switch
⦆
Malfunction of liftgate latch switch
⦆
Malfunction of the front door lock actuator
⦆
Malfunction of luggage compartment light
⦆
Malfunction of the ETACS-ECU
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
LIGHTING
54Ac-151
DIAGNOSIS
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect scan
too (M.U.T.-III) P.54Ac-139."
(2)
Turn the ignition switch to the "ON" position.
(3)
Check whether the ETACS-ECU related DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Diagnose the ETACS-ECU. Refer to GROUP 54Ad,
NO:
Go to Step 2.
STEP 2. Using scan tool MB991958, check data list.
Use the ETACS-ECU service data to check the signals related
to the operation of luggage compartment light.
⦆
Turn the ignition switch to the "LOCK" (OFF) position.
⦆
Remove the ignition key from the ignition key cylinder.
⦆
Open each door.
⦆
Open the liftgate.
Item No.
Item name
Normal
conditions
Item 228
Dr door unlock
ON
Item 254
IG voltage
Battery
voltage
Item 256
Dr door ajar switch
Open
Item 257
As door ajar switch
Open
Item 258
RR door ajar switch Open
Item 259
RL door ajar switch
Open
Item 260
Trunk/gate trunk ajar
switch
Open
Item 264
Handle lock switch
Key in → Key
out
Q:Does scan tool MB991958 display the items "Dr door
unlock", "IG voltage", "Dr door ajar switch", "As door ajar
switch", "RR door ajar switch", "RL door ajar switch",
"Trunk/gate trunk ajar switch" and "Handle lock switch"
as normal condition?
54Ac-152
LIGHTING
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст