Mitsubishi Montero (2004+). Manual — part 1022
HYDRAULIC BRAKE BOOSTER (HBB) DIAGNOSIS
TSB Revision
BASIC BRAKE SYSTEM
35A-87
STEP 4. Check the following harness wire.
• The wire between combination meter connector D-03 (ter-
minal 55) and M-ASTC-ECU connector E-121 (terminal 81)
NOTE: Also check intermediate connector E-111 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector E-111 is damaged, repair
or replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
. If the connector
has been repaired or replaced, go to Step 9.
Q: Is the harness wire damaged?
YES : Repair it and then go to Step 9.
NO : Replace the combination meter (Refer to GROUP
54A, Combination Meter and Vehicle Speed Sensor
) and then go to Step 9.
AC204690 AC
CONNECTOR: D-03
D-03 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
D-03
AC203901
AC204627AR
CONNECTOR: E-121
E-121
E-121
HARNESS CONNECTOR:
COMPONENT SIDE
AC204548AK
CONNECTOR: E-111
E-111
HYDRAULIC BRAKE BOOSTER (HBB) DIAGNOSIS
TSB Revision
BASIC BRAKE SYSTEM
35A-88
STEP 5. Check the combination meter power supply circuit
at combination meter harness connector D-03.
(1) Disconnect combination meter connector D-03, and
measure at the harness connector (component side).
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 62 and ground. The
voltage should measure approximately 12 volts (battery
positive voltage).
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Replace the combination meter (Refer to GROUP
54A, Combination Meter and Vehicle Speed Sensor
) and then go to Step 9.
NO : Go to Step 6.
STEP 6. Check the following connector.
• Combination meter connector D-03
Check connector for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 7.
NO : Repair the faulty connector or terminal and then go to
Step 9.
AC204690 AC
CONNECTOR: D-03
D-03 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
D-03
AC205296
61
62
63
64
65
66
57
58
59
60
51
52
53
54
55
56
67
AB
HARNESS CONNECTOR:
COMPONENT SIDE
D-03
(GR)
AC204690 AC
CONNECTOR: D-03
D-03 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
D-03
HYDRAULIC BRAKE BOOSTER (HBB) DIAGNOSIS
TSB Revision
BASIC BRAKE SYSTEM
35A-89
STEP 7. Check the following harness wire.
• The wire between junction block connector D-208 (terminal
2) and combination meter connector D-03 (terminal 62)
NOTE: Also check intermediate connector D-210 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector D-210 is damaged, repair
or replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
. If the connector
has been repaired or replaced, go to Step 9.
AC204624 AC
CONNECTOR: D-208
D-208
JUNCTION BLOCK
(FRONT VIEW)
D-208 JUNCTION BLOCK
CONNECTOR
AC204690 AC
CONNECTOR: D-03
D-03 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
D-03
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст