Mitsubishi Montero (2004+). Manual — part 870
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-55
STEP 11. Check the harness for short circuit to ground
between A/T control solenoid valve connector C-03
terminal 1 and PCM connector D-135 terminal 119.
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair or replace the harness wire.
AC204395
CONNECTOR : C-03
AE
C-03 (B)
6
10
4
9
5
3
8
2
7
1
AC204681AB
CONNECTOR: D-135
D-135 (GR)
91 92
93
101
94 95
96 97 98 99 100
102103
104
105106
107108 109
110 111112
113114
115116 117
118 119120
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-56
STEP 12. Check A/T control solenoid valve assembly
connector C-03, PCM connector D-135 and intermediate
connector E-114 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 13.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204395
CONNECTOR : C-03
AE
C-03 (B)
6
10
4
9
5
3
8
2
7
1
AC204681AB
CONNECTOR: D-135
D-135 (GR)
91 92
93
101
94 95
96 97 98 99 100
102103
104
105106
107108 109
110 111112
113114
115116 117
118 119120
AC204176
CONNECTOR : E-114
BD
38
28
16
33
22
10
31
19
7
1
18
30
29
17
5
6
21
20
32
8
2
9
25
13
3
24
23
3435
1112
27
26
3637
14
4
15
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-57
STEP 13. Check the harness for open circuit between A/T
control solenoid valve connector C-03 terminal 1 and PCM
connector D-135 terminal 119.
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair or replace the harness wire.
AC204395
CONNECTOR : C-03
AE
C-03 (B)
6
10
4
9
5
3
8
2
7
1
AC204681AB
CONNECTOR: D-135
D-135 (GR)
91 92
93
101
94 95
96 97 98 99 100
102103
104
105106
107108 109
110 111112
113114
115116 117
118 119120
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-58
STEP 14. Measure the ground voltage at PCM connector
D-135 by backprobing.
(1) Do not disconnect connector D-135.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 96 and ground by
backprobing.
• Voltage should measure 0.5 volt or less.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage within the specified range?
YES : Go to Step 15.
NO : Go to Step 17.
AC204681AB
CONNECTOR: D-135
D-135 (GR)
91 92
93
101
94 95
96 97 98 99 100
102103
104
105106
107108 109
110 111112
113114
115116 117
118 119120
AC204918 BQ
D-135 HARNESS CONNECTOR :
HARNESS SIDE
116
97
103
104
112
110 111
106
94 95
98
102
101
100
99
109
115
107
119 120
96
105
91
113
108
117
93
92
114
118
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст