Mitsubishi Montero (2004+). Manual — part 869
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-51
STEP 6. Using scan tool MB991958, check data list item 15:
Transmission Fluid Temperature Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine.
(3) Set scan tool MB991958 to the data reading mode.
• Item 15: Transmission Fluid Temperature Sensor.
• When the engine is cool: Almost equal to the ambi-
ent temperature (atmospheric temperature)
NOTE: Set scan tool MB991958 to the data reading
mode for item number 13, Intake Air Temperature
(IAT) Sensor and note the temperature measure-
ment. When the engine is cool, the temperature
should be almost equal to the ambient temperature
(atmospheric temperature), and the IAT sensor mea-
surement should be approximately the same as the
Transmission Fluid Temperature Sensor.
• When the engine is warm: 70 to 80°C (158 to
176
°F).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
.
NO : Replace the PCM.
STEP 7. Check A/T control solenoid valve assembly
connector C-03 for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 8.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC307591 AC
MB991911
MB991824
MB991827
AC307591
DATA LINK
CONNECTOR
AC204395
CONNECTOR : C-03
AE
C-03 (B)
6
10
4
9
5
3
8
2
7
1
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-52
STEP 8. Measure the resistance of the ground circuit at A/T
control solenoid valve assembly connector C-03.
(1) Disconnect connector C-03 and measure at the harness
side.
(2) Measure the resistance between terminal 2 and ground.
• The resistance should measure less than 2 ohms.
Q: Is the resistance less than 2 ohms?
YES : Go to Step 5.
NO : Go to Step 14.
AC204395
CONNECTOR : C-03
AE
C-03 (B)
6
10
4
9
5
3
8
2
7
1
AC204918
C-03 HARNESS CONNECTOR :
COMPONENT SIDE
CZ
1
8
2
7
9
4
10
5
6
3
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-53
STEP 9. Measure the sensor output voltage at PCM
connector D-135 by backprobing.
(1) Do not disconnect connector D-135.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 119 and ground by
backprobing.
• When transmission fluid temperature is 20°C (68°F),
voltage should measure between 3.8 and 4.0 volts.
• When transmission fluid temperature is 40°C (104°F),
voltage should measure between 3.2 and 3.4 volts.
• When transmission fluid temperature is 80°C (176°F),
voltage should measure between 1.7 and 1.9 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage within the specified range?
YES : Go to Step 12.
NO : Go to Step 10.
AC204681AB
CONNECTOR: D-135
D-135 (GR)
91 92
93
101
94 95
96 97 98 99 100
102103
104
105106
107108 109
110 111112
113114
115116 117
118 119120
AC204918 BR
D-135 HARNESS CONNECTOR :
HARNESS SIDE
116
97
103
104
112
110 111
106
94 95
98
102
101
100
99
109
115
107
119 120
96
105
91
113
108
117
93
92
114
118
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-54
STEP 10. Check A/T control solenoid valve assembly
connector C-03, PCM connector D-135 and intermediate
connector E-114 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 11.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204395
CONNECTOR : C-03
AE
C-03 (B)
6
10
4
9
5
3
8
2
7
1
AC204681AB
CONNECTOR: D-135
D-135 (GR)
91 92
93
101
94 95
96 97 98 99 100
102103
104
105106
107108 109
110 111112
113114
115116 117
118 119120
AC204176
CONNECTOR : E-114
BD
38
28
16
33
22
10
31
19
7
1
18
30
29
17
5
6
21
20
32
8
2
9
25
13
3
24
23
3435
1112
27
26
3637
14
4
15
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст