Mitsubishi Montero (2004+). Manual — part 881
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-99
STEP 6. Measure the PCM output voltage to the speed
sensor at the PCM connector D-134 by backprobing.
(1) Do not disconnect connector D-134.
(2) Disconnect connector C-02 at the output shaft speed
sensor.
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between terminal 73 and ground by
backprobing.
• The voltage should measure between 4.5 and 4.9 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.5 and 4.9 volts?
YES : Go to Step 7.
NO : Go to Step 9.
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204918 BK
D-134 HARNESS CONNECTOR :
HARNESS SIDE
76
85
65
72
71
73
82
75
81
74
63 64
66
70
69
68
67
78
87
79
88 89
80
77
86
62
61
83 84
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-100
STEP 7. Check output shaft speed sensor connector C-02,
PCM connector D-134 and intermediate connector E-114
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connectors in good condition?
YES : Go to Step 8.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204746
CONNECTOR : C-02
C-02 (GR)
AB
1 2 3
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204176
CONNECTOR : E-114
BD
38
28
16
33
22
10
31
19
7
1
18
30
29
17
5
6
21
20
32
8
2
9
25
13
3
24
23
3435
1112
27
26
3637
14
4
15
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-101
STEP 8. Check the harness for open circuit or damage
between output shaft speed sensor connector C-02
terminal 2 and PCM connector D-134 terminal 73.
Q: Is the harness wire in good condition?
YES : Go to Step 19.
NO : Repair or replace the harness wire.
AC204746
CONNECTOR : C-02
C-02 (GR)
AB
1 2 3
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-102
STEP 9. Check output shaft speed sensor connector C-02,
PCM connector D-134 and intermediate connector E-114
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 10.
NO : Repair or replace the damages components. Refer to
GROUP 00E, Harness Connector Inspection
AC204746
CONNECTOR : C-02
C-02 (GR)
AB
1 2 3
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204176
CONNECTOR : E-114
BD
38
28
16
33
22
10
31
19
7
1
18
30
29
17
5
6
21
20
32
8
2
9
25
13
3
24
23
3435
1112
27
26
3637
14
4
15
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст