Mitsubishi Montero (2004+). Manual — part 568
RV METER
TSB Revision
CHASSIS ELECTRICAL
54A-241
8. Press the function switch 1 [NEXT] on this screen. The
vehicle signal status is displayed.
• ILL: ON or OFF
• Key position: "ACC" or "IG"
• Voltage: Battery voltage
• VSS: Vehicle speed
9. Press the function switch 1 [NEXT] on this screen. The
message stating [Automatic diagnosis finished.] is displayed
and within seven seconds later the screen moves to the
screen just before the service mode screen.
.
Diagnosis mode
1. Press the "ADJ" switch with the ignition switch at "LOCK"
(OFF) position, and while keeping on pressing, turn the
ignition switch to the "ACC" or "ON" position. When the
"ADJ" switch is pressed continuously for more than five
seconds, the service function is activated at the same time
with the reception signal (pip sound) and the first menu
screen of the service mode is displayed.
2. Press the function switch 2 [DIAG]. The screen is switched
to the diagnosis mode.
3. When respective function switches are pressed, the screen
is switched as follows.
• When the function switch 1 [VER.] is pressed, versions of
the monitor and the air-conditioner are displayed.
• When the function switch 2 [VEHICLE] is pressed, the sta-
tus of the vehicle signal is displayed.
• When the function switch 3 [COM.] is pressed, the commu-
nication and the connection are checked and the results are
displayed.
• When the "ADJ" switch is pressed, the screen returns to the
service mode second menu screen.
Signal check
ILL
Key position
Voltage
VSS
: OFF
: IG
: 99.9V
: 999km/h
ACX01991
NEXT
AB
Automatic diagnosis finished.
ACX01992
AB
Service mode
ACX01984
AUTO
DIAG.
HISTORY
NEXT
END
AE
SERVICE MODE FIRST MENU SCREEN
Diagnosis
ACX01993
VER.
VEHICLE
COM.
BACK
AB
RV METER
TSB Revision
CHASSIS ELECTRICAL
54A-242
4. Version display screen
Press the function switch1 [VER.]. In the case of
No-automatic A/C circuit or automatic A/C circuit open,
version is not displayed. Press "AD" J [BACK], returns to
Diagnosis display.
NOTE:
.
M: Mitsubishi Electric
D: Denso
5. Vehicle signal status display screen. Press the function
switch 2 [VEHICLE]. Press "ADJ" [BACK], returns to
Diagnosis display.
6. Press the function switch 3 [COM.]. When the ignition key is
at "ACC" position, turn the ignition switch to "ON". Refer to
"Automatic check mode". The check will be finished within
10 seconds after ignition switch "ON" or pressing the
function switch 3[COM.].
7. Communication and connection check results display
screen
• When the function switch 2 is pressed on this screen, the
unit status is displayed.
Version
Monitor
A/C
: M '99/SEP. Ver. xx.x
: D '99/SEP. Ver. xx.x
ACX01994
BACK
Signal check
ILL
Key position
Voltage
VSS
: OFF
: IG
: 99.9V
: 999km/h
ACX01995
BACK
AB
VEHICLE SIGNAL STATUS DISPLAY SCREEN
Checking the system connection.
ACX01986
Please Wait!
AB
Connection status
A/C : Manual or less
Fuel : Full or Disconnected
ACX01996
EXIT
COMMUNICATION AND CONNECTION
CHECK RESULTS DISPLAY SCREEN
AB
Unit status
Monitor : OK
A/C
: E2
ACX01997
EXIT
AB
RV METER
TSB Revision
CHASSIS ELECTRICAL
54A-243
• When the function switch 2 is pressed on this screen, the
inner status of the monitor is displayed.
• Press the function switch 3 on this screen, unit status dis-
played. The inner status of the monitor is displayed.
• Press the function switch" ADJ" [EXIT] to return to diagno-
sis menu.
• Press the function switch "ADJ" [BACK] to service mode
first menu.
.
History mode
1. Press the "ADJ" switch with the ignition switch at "LOCK"
(OFF) position, and while keeping on pressing, turn the
ignition switch to the "ACC" or "ON" position. When the
"ADJ" switch is pressed continuously for more than five
seconds, the service function is activated at the same time
with the reception signal (pip sound) and the first menu
screen of the service mode is displayed.
2. Press the function switch 3 [HISTORY]. The screen is
switched to the history mode.
3. Press the function switch 1 [CLEAR] on this screen,
The number of errors is erased; when the function switch 2
is pressed, the screen is switched to the history mode
second menu screen. When [EXIT] is pressed, the service
mode display returns.
4. When the function switch 1 [CLEAR] is pressed on this
screen, the number of errors is erased; when the function
switch 2 is pressed, the screen switched to the history mode
first menu screen. When [EXIT] is pressed, the service
mode display returns.
.
Monitor status
Amb. Temp. : NG
Geomag. X: OK
Y: OK
Eng. ECU : OK
SWS
M-BUS
: OK
: OK
ACX01998
EXIT
AB
ITEM
DISPLAY
EXAMPLE
CONTENTS OR
CONDITION
Engine-ECU
(Powertrain control
module)
SWS
M-BUS
000
Number of
communication errors
ITEM
DISPLAY
EXAMPLE
CONTENTS OR
CONDITION
Amb. Temp
Geomag. X, Y
000
Number of
connection errors
Service mode
ACX01984
AUTO
DIAG.
HISTORY
NEXT
END
AE
SERVICE MODE FIRST MENU SCREEN
Diag. history
Eng. ECU com. error
SWS com. error
: 999
: 999
: 999
M-BUS com. error
ACX01999
EXIT
CLEAR
AC
XXX
XXX
XXX
Diag. history
Amb. Temp. error
Geomag. X error
: 999
: 999
: 999
Y error
ACX02000
EXIT
CLEAR
AB
HISTORY MODE SECOND SCREEN
RV METER
TSB Revision
CHASSIS ELECTRICAL
54A-244
Monitor check mode
1. Press the "ADJ" switch with the ignition switch at "LOCK"
(OFF) position, and while keeping on pressing, turn the
ignition switch to the "ACC" or "ON" position. When the
"ADJ" switch is pressed continuously for more than five
seconds, the service function is activated at the same time
with the reception signal (pip sound) and the first menu
screen of the service mode is displayed.
2. Press the "ADJ" [NEXT] switch.
The screen is switched to the service mode second menu
screen.
3. Press the function switch 1 [MONITOR]. The screen is
switched to the monitor check mode.
4. When respective function switches are pressed on this
screen, the screen is switched as follows.
• When the function switch 1 [DISP.] is pressed, the screen is
switched to the display check mode.
• When the function switch 2 [COMP.] is pressed, the screen
changes to the geomagnetic sensor check mode.
• When the "ADJ" switch is pressed, the screen changes to
the service mode second menu screen.
.
Display check mode
1. Press the "ADJ" switch with the ignition switch at "LOCK"
(OFF) position, and while keeping on pressing, turn the
ignition switch to the "ACC" or "ON" position. When the
"ADJ" switch is pressed continuously for more than five
seconds, the service function is activated at the same time
with the reception signal (pip sound) and the first menu
screen of the service mode is displayed.
Service mode
ACX01984
AUTO
DIAG.
HISTORY
NEXT
END
AE
SERVICE MODE FIRST MENU SCREEN
Service mode
ACX01985
MONITOR
BACK
END
AB
SERVICE MODE SECOND MENU SCREEN
Monitor check mode
ACX02001
BACK
DISP.
COMP.
AB
MONITOR CHECK MODE SCREEN
Service mode
ACX01984
AUTO
DIAG.
HISTORY
NEXT
END
AE
SERVICE MODE FIRST MENU SCREEN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст