Mitsubishi Montero (2004+). Manual — part 569

RV METER

TSB Revision

CHASSIS ELECTRICAL

54A-245

2. Press the "ADJ" [NEXT] switch is pressed. The screen

changes to the service mode second menu screen.

3. Press the function switch 1 [MONITOR]. The screen is

switched to the monitor check mode.

4. Press the function switch 1 [DISP] on the monitor check

mode screen. The screen changes to the display check
mode screen. When respective function switches are
pressed on this screen, the screen changes as follows.

• When the function switch 1 [COLOR] is pressed, the color

bar is displayed.

• When the function switch 2 [GRAY] is pressed, the gray

scale is displayed.

Service mode

ACX01985

MONITOR

BACK

END

AB

SERVICE MODE SECOND MENU SCREEN

Monitor check mode

ACX02001

BACK

DISP.

COMP.

AB

MONITOR CHECK MODE SCREEN

WHITE YELLOW LIGHT

BLUE GREEN PURPLE RED BLUE BLACK

ACX02006

BACK

COLOR

GRAY

WHITE

AB

COLOR BAR

WHITE

BLACK

ACX02002

BACK

COLOR

GRAY

WHITE

AC

RV METER

TSB Revision

CHASSIS ELECTRICAL

54A-246

• When the function switch 3 [WHITE] is pressed, the white

screen is displayed.

• When the "ADJ" [BACK] is pressed, the service mode dis-

play returns.

.

Geomagnetic sensor check mode
1. Press the "ADJ" switch with the ignition switch at "LOCK"

(OFF) position, and while keeping on pressing, turn the
ignition switch to the "ACC" or "ON" position. When the
"ADJ" switch is pressed continuously for more than five
seconds, the service function is activated at the same time
with the reception signal (pip sound) and the first menu
screen of the service mode is displayed.

2. Press the "ADJ" switch [next].

The screen changes to the service mode second menu
screen.

3. Press the function switch 1 [MONITOR] on the service mode

second menu screen.
The screen is switched to the monitor check mode.

WHITE

ACX02003

BACK

COLOR

GRAY

WHITE

AB

WHITE

Service mode

ACX01984

AUTO

DIAG.

HISTORY

NEXT

END

AE

SERVICE MODE FIRST MENU SCREEN

Service mode

ACX01985

MONITOR

BACK

END

AB

SERVICE MODE SECOND MENU SCREEN

Monitor check mode

ACX02001

BACK

DISP.

COMP.

AB

MONITOR CHECK MODE SCREEN

RV METER

TSB Revision

CHASSIS ELECTRICAL

54A-247

4. Press the function switch 2 [COMP.].

• <Normal case that the body is not magnetized>

The geomagnetic sensor mode screen is displayed. Each of
X- and Y-outputs of the geomagnetic sensor, center coordi-
nates, and radius of the direction circle are displayed. For
degeomagnetization, refer to

P.54A-284

.

• <Case that the body is magnetized>

If the sensor value is outside the range between 450 and
580, it is meant that the body is magnetized. The screen
that calls upon to demagnetize the body stating "Demagne-
tize within range of acceptable level" is displayed. In this
case, it is necessary to demagnetize the body and to cor-
rect the geomagnetic sensor. Refer to on-vehicle ser-
vice-vehicle magnetic compensation

P.34-6

.

• When function switch 1 [CAL.COMP] is pressed at the pre-

vious screen, a message of urging rotation compensation is
displayed. For the method of magnetization compensation
by rotation, refer to

P.54A-284

.

.

Release of service mode
The service mode is released by pressing the "DISP" switch
[END] is pressed on the service mode first screen or the ser-
vice mode second screen, or by turning the ignition switch to
the "LOCK" (OFF) position.

BATTERY DISCONNECTION

When the battery cable is disconnected, the stored data may
disappear. In that case, the system connection should be
checked using the procedure described below

.

Checking connection of system
When the connection data has disappeared, turning the ignition
key to "ACC" position will make the following message appear.
1. Start the engine (or turn the ignition key to "ON" position).

Geomagnetic sensor

Sensor level

X=XXX, Y=XXX

Acceptable X, Y range: (301-722)

Coordi. of C. C. X=XXX, Y=XXX
Radius of D. C. X=XXX,Y=XXX

ACX02004

CAL.COMP

BACK

AC

Geomagnetic sensor

Sensor level

X=XXX, Y=XXX

Acceptable X, Y range: (301-722)

Demagnetise within

range of acceptable level.

AC001241

CAL.COMP

BACK

AC

(430 - 581)

Stat to check the system.

Please turn the ignition key

to the "ON"position

AC001555AB

RV METER

TSB Revision

CHASSIS ELECTRICAL

54A-248

2. When the engine is started or when the ignition key is in the

"ON" position, the monitor will display the message.

3. After a short while the system will beep. When the

connection is completed, the message will be displayed.

TROUBLESHOOTING STRATEGY

M1543006900722

Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find a
combination meter fault.
1. Gather information from the customer.

2. Verify that the condition described by the

customer exists.

3. Find the malfunction by following the symptom

chart.

4. Verify the malfunction is eliminated.

DIAGNOSIS FUNCTION

M1543007000528

HOW TO CONNECT SCAN TOOL (MUT-III)

Required Special Tools:

• MB991958: Scan Tool (MUT-III Sub Assembly)

• MB991824: Vehicle Communication Interface (V.C.I.)

• MB991827: MUT-III USB Cable

• MB991911: MUT-III Main Harness B

CAUTION

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.

Checking the system connection.

Please wait!

AC001553AB

Completed the system connection.

AC001554 AB