Mitsubishi Montero (2004+). Manual — part 510
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-9
6. If there is an immobilizer system DTC, record the
DTC, then erase it from the memory using scan
tool MB991958.
7. Recreate the immobilizer system DTC set
conditions to see if the same immobilizer system
DTC will resets.
(1) If the same immobilize system DTC resets,
perform the appropriate diagnostic procedure.
Refer to Diagnostic Trouble Code Chart
.
(2) If the same immobilizer system DTC does not
reset, the malfunction is intermittent. Refer to
GROUP 00, How to Use
Troubleshooting/inspection Service Points
−
How to Cope with Intermittent Malfunctions
IMMOBILIZER SYSTEM TROUBLE CODE
DIAGNOSIS
M1543007000476
Retrieving and Erasing Immobilizer System
Diagnostic Trouble Codes
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
1. Ensure that the ignition switch is at the "LOCK" (OFF)
position.
2. Start up the personal computer.
3. Connect special tool MB991827 to special tool MB991824
and the personal computer.
4. Connect special tool MB991911 to special tool MB991824.
5. Connect special tool MB991911 to the data link connector.
6. Turn the power switch of special tool MB991824 to the "ON"
position.
NOTE: When special tool MB991824 is energized, special
tool MB991824 indicator light will be illuminated in a green
color.
7. Start the MUT-III system on the personal computer.
NOTE: Disconnecting scan tool MB991958 is the reverse of
the connecting sequence, making sure that the ignition
switch is at the "LOCK" (OFF) position.
HOW TO READ AND ERASE DIAGNOSTIC
TROUBLE CODES
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
AC306409AF
MB991911
MB991824
MB991827
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-10
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
NOTE: If the battery voltage is low, diagnostic trouble codes will
not be set. Check the battery if scan tool MB991958 does not
display.
1. Connect scan tool MB991958 to the data link connector.
2. Turn the ignition switch to "ON" position.
3. Select "Interactive Diagnosis" from the start-up screen.
4. Select "System select."
5. Choose "IMMOBILIZER" from the "POWER TRAIN" tab.
6. Select "MITSUBISHI".
7. Select "Diagnostic Trouble Code."
8. If a DTC is set, it is shown.
9. Choose "Erase DTCs" to erase the DTC.
HOW TO READ DATA LIST
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
AC306409AF
MB991911
MB991824
MB991827
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-11
1. Connect scan tool MB991958 to the data link connector.
2. Turn the ignition switch to "ON" position.
3. Select "Interactive Diagnosis" from the start-up screen.
4. Select "System select."
5. Choose "IMMOBILIZER" from the "POWER TRAIN" tab.
6. Select "Data List."
7. Choose an appropriate item and select the "OK" button.
DIAGNOSTIC TROUBLE CODE CHART
M1543007100451
CAUTION
During diagnosis, a DTC code associated with
other system may be set when the ignition switch
is turned on with connector(s) disconnected. On
completion, confirm all systems for DTC code(s).
If DTC code(s) are set, erase them all.
Use the following chart to develop proper diagnostic
strategy.
AC306409AF
MB991911
MB991824
MB991827
DIAGNOSTIC
TROUBLE CODE NO.
DESCRIPTION
REFERENCE PAGE
11
Transponder communication system or radio interference
of encrypted code
12
Encrypted codes are not the same or are not registered
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-12
DIAGNOSTIC TROUBLE CODE PROCEDURES
DTC 11: Transponder Communication System or Radio Interference of Encrypted Code
.
CIRCUIT OPERATION
The ignition key is powered by the ignition key ring
antenna. The ignition key then sends an encrypted
code. The ignition key ring antenna receives the
encrypted code, and determines if the ignition key is
registered.
.
DTC SET CONDITION
• DTC 11 may be set if other ignition keys are in the
vicinity of the vehicle as it is being started.
• The transponder’s encrypted code is not sent to
the immobilizer-ECU immediately after the igni-
tion switch is turned to "ON" position.
NOTE: DTC 11 is always set together with MFI sys-
tem DTC P1610.
.
TROUBLESHOOTING HINTS
• Radio interference of the encrypted code
• Malfunction of the transponder
• Malfunction of the ignition key ring antenna
• Malfunction of the immobilizer-ECU
• Damaged wiring harness of connectors
.
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: Scan Tool (MUT-III Sub Assembly)
IMMOBILIZER-
ECU
IGNITION KEY
RING ANTENNA
TRANSPONDER
HIGH FREQUENCY
CIRCUIT
Ignition Key Ring Antenna Circuit
AC204170
CONNECTOR : D-121
DN
AC204172
CONNECTOR : D-201
AJ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст