Mitsubishi Montero (2004+). Manual — part 1141
TOE CONTROL ARM ASSEMBLY AND TOE CONTROL TOWER BAR
TSB Revision
REAR SUSPENSION
34-23
2. Apply multipurpose grease to the inside of the dust cover as
shown.
3. Apply multipurpose grease to the shown parts inside the
dust cover and the ball joint stud.
4. Wrap plastic tape around the toe control arm ball joint stud,
and then install the dust cover to the toe control arm ball
joint.
CAUTION
Do not apply grease to the place (tapered section) where
the threaded section of the ball joint connects with the
knuckle. Wipe the grease off if it is applied in this area. To
prevent the grease from being applied to the ball joint con-
nection (taper) with the knuckle, do not compress the dust
cover before installation.
5. Using the special tool, drive the dust cover into the position
shown in the illustration.
6. Press the dust cover with your finger to check that there are
no cracks or damage in the dust cover.
ACX00726 AB
30 mm
(1.18 in)
OR MORE
ACX00747AB
DUST
COVER
MB990800
TRAILING ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-24
TRAILING ARM ASSEMBLY
REMOVAL AND INSTALLATION
M1341004200103
CAUTION
*: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in an unladen condition.
TRAILING ARM BUSHING REPLACEMENT
M1341011300113
Required Special Tool:
• MD998236: Output Shaft Bearing Installer
1. Use special tool MD998236 to drive in/out the bushing
from/to the trailing arm.
Post-installation Operation
• Wheel Alignment Check and Adjustment (Refer to
.)
ACX00748 AC
1
3
2
213
± 34 N
·
m *
157
± 25 ft-lb *
4
213
± 34 N
·
m
157
± 25 ft-lb
REMOVAL STEPS
1. TRAILING ARM TO KNUCKLE
SECURING BOLT
2. TRAILING ARM TO REAR FRAME
SECURING NUT
3. STOPPER
4. TRAILING ARM
REMOVAL STEPS (Continued)
ACX00749
MD998236
TRAILING ARM
AC
SPECIFICATIONS
TSB Revision
REAR SUSPENSION
34-25
2. When assembling, apply soapy water around the bushing
and the inner diameter of the trailing arm, and then drive in
the bushing so that it protrudes by the same amount at
either side and its hollow part is as shown.
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1341012700233
ACX0750 AC
HOLLOW PART
ITEM
SPECIFICATION
Rear suspension assembly
Brake tube flare nut
15
± 2 N⋅m (11 ± 2 ft-lb)
Crossmember mounting nut
167
± 19 N⋅m (123 ± 14 ft-lb)
Nut securing lower arm to knuckle assembly
152
± 25 N⋅m (113 ± 18 ft-lb)
Nut securing lower arm to body
123
± 15 N⋅m (91 ± 11 ft-lb)
Nut securing shock absorber to lower arm assembly 152
± 25 N⋅m (113 ± 18 ft-lb)
Nut securing trailing arm to rear frame
213
± 34 N⋅m (157 ± 25 ft-lb)
Propeller shaft assembly nut
60
± 10 N⋅m (45 ± 7 ft-lb)
Rear disc brake assembly mounting bolt
88
± 10 N⋅m (65 ± 7 ft-lb)
Upper arm assembly
Brake pipe connection
15
± 2 N⋅m (11 ± 2 ft-lb)
Nut securing upper arm assembly to rear frame
167
± 10 N⋅m (124 ± 7 ft-lb)
Nut securing upper arm ball joint to knuckle
150
± 30 N⋅m (111 ± 22 ft-lb)
Nut securing upper arm to upper arm ball joint
assembly
98
± 12 N⋅m (72 ± 9 ft-lb)
Stabilizer link mounting nut
104
± 14 N⋅m (77 ± 10 ft-lb)
Shock absorber, coil spring and lower arm assembly
Nut securing lower arm to knuckle assembly
152
± 25 N⋅m (113 ± 18 ft-lb)
Nut securing lower arm to body
123
± 15 N⋅m (91 ± 11 ft-lb)
Nut securing shock absorber to lower arm assembly 152
± 25 N⋅m (113 ± 18 ft-lb)
Shock absorber connecting nut
44
± 10 N⋅m (33 ± 7 ft-lb)
Stabilizer bar
Stabilizer clamp mounting bolt
44
± 10 N⋅m (33 ± 7 ft-lb)
Toe control arm assembly, toe control tower bar
Nut securing toe control arm ball joint to knuckle
67
± 7 N⋅m (50 ± 5 ft-lb)
Nut securing toe control arm to rear frame
123
± 15 N⋅m (91 ± 11 ft-lb)
Toe control tower bar mounting bolt, nut
46
± 8 N⋅m (34 ± 6 ft-lb)
SPECIFICATIONS
TSB Revision
REAR SUSPENSION
34-26
GENERAL SPECIFICATIONS
M1341000200305
COIL SPRING
SERVICE SPECIFICATIONS
M1341000300272
Trailing arm assembly
Nut securing trailing arm to knuckle
213
± 34 N⋅m (157 ± 25 ft-lb)
Nut securing trailing arm to rear frame
213
± 34 N⋅m (157 ± 25 ft-lb)
ITEM
SPECIFICATION
ITEM
LS
except LS
Wire diameter mm (in)
18
− 19 (0.71 − 0.75)
17 (0.67)
Average diameter mm (in)
133
− 134 (5.24 − 5.28)
132
− 134 (5.20 − 5.28)
Free length mm (in)
337 (13.3)
343 (13.5)
ITEM
SPECIFICATION
Toe-in mm (in)
3
± 3 (0.12 ± 0.12)
Camber
0
°00' ± 30' (Left/right deviation within 30')
Upper arm ball joint turning torque N
⋅m (in-lb)
1.5
− 7.9 (13 − 70)
Stabilizer link ball joint turning torque N
⋅m (in-lb)
0.5
− 2.0 (4 − 17)
Toe control arm ball joint turning torque N
⋅m (in-lb)
0.7
− 1.0 (6 − 9)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст