Mitsubishi Montero (2004+). Manual — part 1139
SHOCK ABSORBER, COIL SPRING AND LOWER ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-15
UPPER ARM BALL JOINT DUST COVER CHECK
1. Press the dust cover with your finger to check that there are
no cracks or damage in the dust cover.
2. If the dust cover is cracked or damaged, replace the upper
arm ball joint assembly.
NOTE: If the dust cover is cracked or damaged, it is possible
that there may also be damage to the ball joint.
SHOCK ABSORBER, COIL SPRING AND LOWER ARM
ASSEMBLY
REMOVAL AND INSTALLATION
M1341014200063
CAUTION
*: indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in the unladen condition.
Post-removal Operation
• Wheel Alignment Check and Adjustment (Refer to
.)
ACX00739
123
± 15 N
·
m *
91
± 11 ft-lb *
44
± 10 N
·
m *
33
± 7 ft-lb *
152
± 25 N
·
m *
113
± 18 ft-lb *
5
8
9
4
2
3
1
6
7
AB
152
± 25 N
·
m *
113
± 18 ft-lb *
SHOCK ABSORBER, COIL SPRING AND LOWER ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-16
REMOVAL SERVICE POINTS
.
<<A>> LOWER ARM MOUNTING BOLT REMOVAL
1. Place a piece of wood at the lower arm as shown in the
illustration. Using the floor jack, compress the coil spring to
remove the lower arm mounting bolt.
2. Lower the floor jack slowly, and then remove the coil spring.
.
<<B>> BOLT ASSEMBLY (CAMBER ADJUSTING BOLT)
REMOVAL
Make the mating marks to the bracket and the camber adjust-
ing bolt, and then remove the camber adjusting bolt.
INSTALLATION SERVICE POINT
.
>>A<< COIL SPRING/LOWER ARM MOUNTING BOLT
INSTALLATION
1. The identification color of the coil spring should be located at
the lower side.
2. Align the coil spring end with the spring lower pad cavity.
SHOCK ABSORBER REMOVAL
STEPS
1. SHOCK ABSORBER MOUNTING
NUT
2. SHOCK ABSORBER MOUNTING
BOLT
3. SHOCK ABSORBER
COIL SPRING REMOVAL STEPS
2. SHOCK ABSORBER MOUNTING
BOLT
<<A>> >>A<<
4. LOWER ARM MOUNTING BOLT
>>A<<
5. COIL SPRING
6. SPRING UPPER PAD
7. SPRING LOWER PAD
LOWER ARM REMOVAL STEPS
2. SHOCK ABSORBER MOUNTING
BOLT
<<A>> >>A<<
4. LOWER ARM MOUNTING BOLT
>>A<<
5. COIL SPRING
6. SPRING UPPER PAD
7. SPRING LOWER PAD
<<B>>
8. BOLT ASSEMBLY (CAMBER
ADJUSTING BOLT)
9. LOWER ARM ASSEMBLY
COIL SPRING REMOVAL STEPS
AC204512 AB
PIECE OF
WOOD
ACX00734AB
LOWER ARM
CAMBER
ADJUSTMENT
BOLT
SHOCK ABSORBER, COIL SPRING AND LOWER ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-17
3. Place a piece of wood at the lower arm as shown in the
illustration. Using the floor jack, compress the coil spring to
remove the lower arm mounting bolt.
LOWER ARM BUSHING REPLACEMENT
M1341011800118
Required Special Tool:
• MB990881: Rear Suspension Bushing Arbor
Use special tool MB990881 to drive out and press-fit the lower
arm bushing.
AC204512 AB
PIECE OF
WOOD
ACX00742AB
LOWER ARM
ASSEMBLY
MB990881
STABILIZER BAR
TSB Revision
REAR SUSPENSION
34-18
STABILIZER BAR
REMOVAL AND INSTALLATION
M1341001300093
INSTALLATION SERVICE POINT
.
>>A<< BUSHING INSTALLATION
1. Install the stabilizer bar so that its identification mark faces
the left side of the vehicle.
2. Install the bushing so that its slit faces the direction shown in
the illustration.
Post-installation Operations
• Press the dust cover with your finger to check that there
are no cracks or damage in the dust cover.
ACX00743
44
± 10 N
·
m
33
± 7 ft-lb
104
± 14 N
·
m
77
± 10 ft-lb
1
4
2
3
1
AC
104
± 14 N
·
m
77
± 10 ft-lb
REMOVAL STEPS
1. STABILIZER LINK ASSEMBLY
2. STABILIZER CLAMP
>>A<<
3. BUSHING
4. STABILIZER BAR
REMOVAL STEPS (Continued)
ACX0744 AB
FRONT
BUSHING
STABILIZER BAR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст