Mitsubishi Montero (2004+). Manual — part 1081

M-ASTC DIAGNOSIS

TSB Revision

MITSUBISHI ACTIVE SKID AND TRACTION CONTROL SYSTEM

35C-35

STEP 1. Using scan tool MB991958, check data list.

CAUTION

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector

(16-pin).

(2) Turn the ignition switch to the "ON" position.
(3) When the steering wheel is turned, data list following item

should change.

• Item 32: ST ANGLE

Q: When the steering wheel is turned, does data list item

32 change?
YES : Go to Step 11.
NO : Go to Step 2.

STEP 2. Check the battery power supply to the steering
wheel sensor. Measure at steering wheel sensor connector
D-225.

(1) Disconnect steering wheel sensor connector D-225, and

measure the voltage at the harness-side connector.

(2) Measure the voltage between steering wheel sensor

connector D-225 terminal 1 and body ground.

• The voltage should measure battery voltage (approxi-

mately 12 volts).

Q: Does the voltage measure battery voltage

(approximately 12 volts)?
YES : Go to Step 5.
NO : Go to Step 3.

AC307591 AC

MB991911

MB991824

MB991827

AC307591

DATA LINK

CONNECTOR

AC204172

CONNECTOR: D-225

HARNESS SIDE

AD

3 2

1

4

5

AC204580

3 2

1

4

5

HARNESS SIDE: D-225

AR

M-ASTC DIAGNOSIS

TSB Revision

MITSUBISHI ACTIVE SKID AND TRACTION CONTROL SYSTEM

35C-36

STEP 3. Check steering wheel sensor connector D-225.

Q: Is steering wheel sensor connector D-225 in good

condition?
YES : Go to Step 4.
NO : Repair or replace the connector, and then go to Step

12.

STEP 4. Check the wiring harness between steering wheel
sensor connector D-225 terminal 1 and fusible link No.1.

NOTE: Also check joint connector D-02 and intermediate con-
nector D-28 for loose, corroded, or damaged terminals, or ter-
minals pushed back in the connectors. If joint connector D-02
or intermediate connector D-28 are damaged, repair or replace
the damaged component(s) as described in GROUP 00E, Har-
ness Connector Inspection

P.00E-2

. If the connector has been

repaired or replaced, go to Step 12.
Q: Is the wiring harness between steering wheel sensor

connector D-225 terminal 1 and the fusible link No.1 in
good condition?
YES : Go to Step 12.
NO : Repair the wiring harness, and then go to Step 12.

AC204172

CONNECTOR: D-225

HARNESS SIDE

AD

3 2

1

4

5

AC204172

CONNECTOR: D-225

HARNESS SIDE

AD

3 2

1

4

5

AC204188

CONNECTORS: D-02, D-28

D-02

D-02

D-28

AB

D-28

9 10

8

6 7

31 32

30

29

18 19 20 21

5

4

2

1

3

27

26

24

23

25

12 13 14 15 16 17

28

11
22
33

2 3

27

32

28

33

16

15

4 5

19

18

29

17

34

7 8

35

22

21

9 10

30

36

31

37

25

24

23

6

20

1

14

26

11

13

12

38

M-ASTC DIAGNOSIS

TSB Revision

MITSUBISHI ACTIVE SKID AND TRACTION CONTROL SYSTEM

35C-37

STEP 5. Check the battery power supply to the steering
wheel sensor. Measure at steering wheel sensor connector
D-225.

(1) Disconnect steering wheel sensor connector D-225, and

measure the voltage at the harness-side connector.

(2) Turn the ignition switch to the "ON" position.

(3) Measure the voltage between steering wheel sensor

connector D-225 terminal 2 and body ground.

• The voltage should measure battery voltage (approxi-

mately 12 volts).

Q: Does the voltage measure battery voltage

(approximately 12 volts)?
YES : Go to Step 8.
NO : Go to Step 6.

STEP 6. Check steering wheel sensor connector D-225.

Q: Is steering wheel sensor connector D-225 in good

condition?
YES : Go to Step 7.
NO : Repair or replace the connector, and then go to Step

12.

STEP 7. Check the wiring harness between steering wheel
sensor connector D-225 terminal 2 and ignition switch

(IG2).

AC204172

CONNECTOR: D-225

HARNESS SIDE

AD

3 2

1

4

5

AC204580

3 2

1

4

5

HARNESS SIDE: D-225

AS

AC204172

CONNECTOR: D-225

HARNESS SIDE

AD

3 2

1

4

5

AC204172

CONNECTOR: D-225

HARNESS SIDE

AD

3 2

1

4

5

M-ASTC DIAGNOSIS

TSB Revision

MITSUBISHI ACTIVE SKID AND TRACTION CONTROL SYSTEM

35C-38

NOTE: Also check joint connector D-01 and junction block con-
nector D-208 and D-210 for loose, corroded, or damaged termi-
nals, or terminals pushed back in the connectors. If joint
connector D-01 or junction block connector D-208 or D-210 are
damaged, repair or replace the damaged component(s) as
described in GROUP 00E, Harness Connector Inspection

P.00E-2

. If the connector has been repaired or replaced, go to

Step 12.
Q: Is the wiring harness between steering wheel sensor

connector D-225 terminal 2 and the ignition switch (IG2)
in good condition?
YES : Go to Step 12.
NO : Repair the wiring harness, and then go to Step 12.

AC204170

CONNECTOR: D-01

AB

9 10

8

6 7

31 32

30

29

18 19 20 21

5

4

2

1

3

27

26

24

23

25

12 13 14 15 16 17

28

11
22
33

AC204191

CONNECTORS: D-208, D-210

D-208

AC

HARNESS SIDE

HARNESS SIDE

D-210

D-208

D-210

1

2

3

5

6

4

1

2

7 6

3

9

4

11

12

10

13

5

8