Mitsubishi Montero (2004+). Manual — part 708
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-89
STEP 2. Use scan tool MB991958 to select "ECU COMM
CHK" on the SWS monitor display.
Check the following ECUs:
• ETACS-ECU
• RV meter
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect the special tool. Refer to "How to connect SWS
monitor
(2) Connect SWS monitor kit MB991862 to the data link
connector (13-pin).
(3) Turn the ignition switch to the "LOCK" (OFF) position.
(4) Operate scan tool MB991958 according to the procedure
below to display "ECU COMM CHK."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "ECU COMM CHK."
(5) Scan tool MB991958 should show "OK" on the "ECU
COMM CHK" menus for both the "ETACS ECU" and the
"CENTER DISP." menus.
Q: Is "OK" displayed on both the "ETACS ECU" and
"CENTER DISP." menu?
"OK" are displayed for all the items : Go to Step 3.
"NG" is displayed on the "ETACS ECU" menu : Refer to
Inspection Procedure A-3 "Communication with
ETACS-ECU is not possible
"NG" is displayed on the "CENTER DISP." menu : Refer
to Inspection procedure A-6 "Communication with RV
meter is not possible
AC309091
MB991911
MB991827
MB991824
AB
MB991806
MB991862
DATA LINK
CONNECTOR
(16-PIN)
DATA LINK
CONNECTOR
(13-PIN)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-90
STEP 3. Check the input signal by using "FUNCTION
DIAG." menu of the SWS monitor.
Turn the ignition switch to the "ON" position to check the input
signals from the following switches.
Operate scan tool MB991958 according to the procedure below
to display "CENTR. DIS. ALM."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "FUNCTION DIAG."
5. Select "BUZZER."
6. Select "CENTR. DIS. ALM."
When the RV meter display switch is operated, check that nor-
mal conditions are displayed on the items described in the table
below.
Q: Are normal conditions displayed on the "BUZZER" and
"beep data"?
Normal conditions are displayed for all the items :
Replace the ETACS-ECU. Verify that the RV meter
operating sound function works normally.
The scan tool does not show the respective normal
condition for item "BUZZER." : Replace the ETACS-ECU.
Verify that the RV meter operating sound function
works normally.
The scan tool does not show the respective normal
condition for item "beep data." : Refer to Inspection
Procedure O-10 "ETACS-ECU does not receive
signals from any control switches
ITEM NO.
ITEM NAME
NORMAL
CONDITION
ITEM 43
BUZZER
ON
ITEM 60
beep data
ON (2 kHz)
AC309091
MB991911
MB991827
MB991824
AB
MB991806
MB991862
DATA LINK
CONNECTOR
(16-PIN)
DATA LINK
CONNECTOR
(13-PIN)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-91
CENTRAL DOOR LOCKING SYSTEM
GENERAL DESCRIPTION CONCERNING THE CENTRAL DOOR LOCKING SYSTEM
M1549021100088
The following ECUs affect the functions and control
of the central door locking system.
Door lock function
.
Operating the driver’s or front passenger’s door lock key
cylinder
When you insert the ignition key to the driver’s or front passen-
ger’s door lock key cylinder and turn the key clockwise to lock
the door, the ETACS-ECU energizes its door lock relay for 0.5
second to activate all the door lock actuators. Then all the
doors will be locked.
.
FUNCTION
CONTROL ECU
Door lock function
Operating the driver’s or front passenger’s door lock key
cylinder
ETACS-ECU
Operating the driver’s or front passenger’s door lock switch
Operating the driver’s door inside lock knob
Door unlock function
Operating the driver’s door lock key cylinder
Operating the front passenger’s door lock key cylinder
Operating the driver’s or front passenger’s door lock switch
Forgotten key prevention function
AC203730AB
ON
(LOCK)
OFF
DRIVER'S OR
PASSENGER'S
DOOR LOCK
KEY CYLINDER
SWITCH
0.5 second
OFF
ON
LOCK RELAY
OUTPUT
ALL DOOR'S
LOCK
ACTUATOR
UNLOCK
LOCK
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-92
Operating the driver’s or front passenger’s door lock
switch
When the door is locked by driver’s or front passenger’s door
lock switch, the ETACS-ECU energizes its door lock relay for
0.5 second to activate all the door lock actuators. Then all the
doors will be locked.
.
Operating the driver’s door inside lock knob
When the door is locked by driver's door inside lock knob, the
ETACS-ECU energizes its door lock relay for 0.5 second to
activate all the door lock actuators. Then all the doors will be
locked.
Door unlock function
.
Operating the driver’s door lock key cylinder
When you insert the ignition key to the driver’s door lock key
cylinder and turn the key counterclockwise to unlock the door,
the ETACS-ECU energizes its door unlock relay for 0.5 second
to activate only the driver’s door lock actuator. Then only the
driver’s door will be unlocked.
When you turn the key counterclockwise again, the
ETACS-ECU energizes its door unlock relay for 0.5 second to
activate all the door lock actuator. Then all the doors will be
unlocked.
.
AC203009
ON(LOCK)
ON(UNLOCK)
OFF
t: 0.5 second
OFF
ON
DRIVER'S OR
FRONT
PASSENGER'S
DOOR LOCK
SWITCH
LOCK RELAY
OUTPUT
ALL DOOR'S
LOCK ACTUATOR
UNLOCK
LOCK
AC
t
AC202980AC
UNLOCK
LOCK
t: 0.5 second
OFF
ON
UNLOCK
LOCK
t
DRIVER'S DOOR
INSIDE LOCK KNOB
LOCK RELAY OUTPUT
ALL DOOR'S LOCK
ACTUATOR
AC200017AD
ON
(UNLOCK)
OFF
DRIVER'S
DOOR LOCK
KEY CYLINDER
SWITCH
t: 0.5 second
BACK DOOR
LOCK
ACTUATOR
OFF
ON
UNLOCK RELAY
OUTPUT
LOCK
UNLOCK
LOCK
UNLOCK
DRIVER'S
DOOR LOCK
ACTUATOR
UNLOCK
LOCK
t
PASSESNGER'S
DOOR LOCK
ACTUATOR
t
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст