Mitsubishi Montero (2004+). Manual — part 519
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-45
STEP 3. Check combination meter connector D-03 and
vehicle speed sensor connector C-08 for loose, corroded
or damaged terminals, or terminals pushed back in the
connector.
Q: Are combination meter connector D-03 and vehicle
speed sensor connector C-08 in good condition?
YES : Go to Step 4.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. The speedometer should work normally.
STEP 4. Check the wiring harness between combination
meter connector D-03 (terminal 65) and vehicle speed
sensor connector C-08 (terminal 3).
AC204395
CONNECTOR : C-08
C-08(B)
C-08(B)
HARNESS SIDE
AI
3 2 1
AC204170
CONNECTOR : D-03
AC
D-03(GR)
HARNESS
SIDE
51
52
61 60
53
54
56
57
55
63
66 65 64
59
62
58
67
D-03(GR)
AC204395
CONNECTOR : C-08
C-08(B)
C-08(B)
HARNESS SIDE
AI
3 2 1
AC204170
CONNECTOR : D-03
AC
D-03(GR)
HARNESS
SIDE
51
52
61 60
53
54
56
57
55
63
66 65 64
59
62
58
67
D-03(GR)
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-46
NOTE: Also check intermediate connector E-111, E-114 and
joint connector (4) D-116. If intermediate connector E-111,
E-114 or joint connector (4) D-116 are damaged, repair or
replace the connector as described in GROUP 00E, Harness
Connector Inspection
.
Q: Is the wiring harness between combination meter
connector D-03 (terminal 65) and vehicle speed sensor
connector C-08 (terminal 3) in good condition?
YES : Go to Step 5.
NO : Repair the wiring harness. The speedometer should
work normally.
STEP 5. Check the speedometer by operating the
auto-cruise control system.
Q: Does auto-cruise control work normally?
YES : Replace the combination meter. The speedometer
should work normally.
NO : Replace the PCM. The speedometer should work
normally.
AC204171
CONNECTOR : D-116
AD
9 10
8
6 7
31 32
30
29
18 19 20 21
5
4
2
1
3
27
26
24
23
25
12 13 14 15 16 17
28
11
22
33
AC204194
CONNECTORS : E-111, E-114
E-111
AB
E-114
E-111
E-114
10
9
31
30
20 21
7
6
28
17 18
8
19
29
4
3
25 26
14 15
1
23
12
2
13
24
5
16
27
11
22
32
10
9
31
30
20 21
7
6
28
17 18
8
19
29
4
3
25 26
14 15
1
23
12
2
13
24
5
16
27
11
22
32
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-47
INSPECTION PROCEDURE 2: Tachometer does not Work.
COMBINATION
METER
TACHO
METER
POWERTRAIN
CONTROL
MODULE
JOINT
CONNECTOR (5)
CPU
Tachometer Circuit
AC204170
CONNECTORS : D-03, D-29
DE
D-03(GR)
D-29
AC204171
CONNECTOR : D-134
AW
D-134(GR)
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-48
.
CIRCUIT OPERATION
• The tachometer power is supplied from the igni-
tion switch (IG) circuit.
• The tachometer detects the ignition signal control
via the PCM.
.
TECHNICAL DESCRIPTION (COMMENT)
The ignition signal may not be sent from the engine,
or there may be a malfunction in the power supply or
ground circuit.
.
TROUBLESHOOTING HINTS
• Malfunction of the combination meter (printed cir-
cuit board or speedometer and tachometer)
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
• Malfunction of the PCM
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
STEP 1. Check the tachometer by observing the other
meters.
Check to see that the speedometer, fuel gauge and water ther-
mometer operate normally.
Q: Do all other meters operate?
YES <other meters all operate> : Go to Step 2.
NO <one of the meters do not operate > : Refer to
INSPECTION PROCEDURE 5
.
AC204176
CONNECTOR: E-111
AK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст