Mitsubishi Montero (2004+). Manual — part 518
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-41
1. Ensure that the ignition switch is at the "LOCK" (OFF)
position.
2. Start up the personal computer.
3. Connect special tool MB991827 to special tool MB991824
and the personal computer.
4. Connect special tool MB991911 to special tool MB991824.
5. Connect special tool MB991911 to the data link connector.
6. Turn the power switch of special tool MB991824 to the "ON"
position.
NOTE: When special tool MB991824 is energized, special
tool MB991824 indicator light will be illuminated in a green
color.
7. Start the MUT-III system on the personal computer.
NOTE: Disconnecting scan tool MB991958 is the reverse of
the connecting sequence, making sure that the ignition
switch is at the "LOCK" (OFF) position.
SYMPTOM CHART
M1543007200771
AC306409AF
MB991911
MB991824
MB991827
SYMPTOM
INSPECTION
PROCEDURE
REFERENCE PAGE
Speedometer does not work.
1
Tachometer does not work.
2
Fuel gauge does not work.
3
Engine coolant temperature gauge does not work.
4
Combination meter does not work.
5
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-42
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Speedometer does not Work.
COMBINATION
METER
CPU
SPEED
METER
VEHICLE SPEED
SENSOR
JOINT
CONNECTOR (4)
Speedometer Circuit
AC204395
CONNECTOR : C-08
AJ
C-08(B)
AC204170
CONNECTOR : D-03
DC
D-03(GR)
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-43
.
CIRCUIT OPERATION
• The ignition switch (IG1) circuit is the power sup-
ply for the speedometer and vehicle speed sen-
sor.
• The vehicle speed sensor is installed on the
transmission. Four pulses are generated with one
turn of the vehicle speed sensor shaft. These
pulse signals are sent into the PCM and sent into
the speedometer. The speedometer calculates
the pulse signals, and operates the indicator. At
the same time, the travel distance is calculated.
.
TECHNICAL DESCRIPTION (COMMENT)
The cause may be a faulty vehicle speed sensor cir-
cuit system or a faulty speedometer. The vehicle
speed sensor is also used by the powertrain control
module (PCM), the auto-cruise control-ECU.
.
TROUBLESHOOTING HINTS
• Malfunction of the vehicle speed sensor
• Malfunction of the combination meter (printed-cir-
cuit board or speedometer and tachometer)
• Malfunction of the PCM
• Malfunction of the auto-cruise control-ECU
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
STEP 1. Check the speedometer by observing the other
meters.
Check to see that the tachometer, fuel gauge and water ther-
mometer are operating normally.
Q: Do all other meters operate?
YES <other meters all operate> : Go to Step 2.
NO <one of the meters do not operate> : Refer to
INSPECTION PROCEDURE 5
.
AC204171
CONNECTOR : D-116
AI
AC204176
CONNECTORS : E-111, E-114
E-111
AL
E-114
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-44
STEP 2. Using scan tool MB991958, read the MFI system
diagnostic trouble code.
CAUTION
To prevent damage to scan tool MB991958 always turn the
ignition switch to "LOCK" (OFF) position before connect-
ing or disconnecting scan tool.
1. Connect scan tool MB991958 to the data link connector.
2. Turn the ignition switch "ON" position.
3. Check the MFI system diagnostic trouble code.
Q: Are MFI system-related DTC(s) sets to the MFI system?
YES : Refer to GROUP 13A, Multiport Fuel Injection (MFI)
.
NO : Go to Step 3.
AC306409AF
MB991911
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст