Mitsubishi Montero (2004+). Manual — part 855
OUTSIDE MIRROR
TSB Revision
EXTERIOR
51-41
REMOVAL SERVICE POINT
.
<<A>> MIRROR REMOVAL
Push the top of the mirror with your hand to tilt it and attach the
protective tape as shown in the illustration. Then insert a
flat-tipped screwdriver in between the notch at the rear of the
mirror and the pivot plate, and disengage the bottom of the mir-
ror.
INSTALLATION SERVICE POINT
.
>>A<< MIRROR INSTALLATION
While supporting the clip position on the underside of the pivot
plate with a flat-tipped screwdriver, press the clip at the front of
the mirror to engage the bottom of the mirror.
AC000441
00007256
MIRROR
FLAT-TIPPED
SCREWDRIVER
SECTION A – A
PIVOT PLATE
NOTCH
PROTECTIVE
TAPE
A
A
A
A
AB
AC000442
00007258
MIRROR
FLAT-TIPPED
SCREWDRIVER
SECTION A – A
PIVOT PLATE
A
A
A
A
AB
OUTSIDE MIRROR
TSB Revision
EXTERIOR
51-42
INSPECTION
M1511019100608
REMOTE CONTROLLED MIRROR ASSEMBLY
CHECK
REMOTE CONTROLLED MIRROR SWITCH
CONTINUITY CHECK
BATTERY CONNECTION
SPECIFIED CONDITION
• Connect terminal 6 to the
negative battery terminal
• Connect terminal 4 to the
positive battery terminal
Mirror glass should face
upward
• Connect terminal 4 to the
negative battery terminal
• Connect terminal 6 to the
positive battery terminal
Mirror glass should face
downward
• Connect terminal 5 to the
negative battery terminal
• Connect terminal 6 to the
positive battery terminal
Mirror glass should face to
the right
• Connect terminal 6 to the
negative battery terminal
• Connect terminal 5 to the
positive battery terminal
Mirror glass should face to
the left
AC000443
SWITCH POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Left side
Up
1
− 6, 9 − 11
Less than 2
ohms
Down
1
− 11, 6 − 9
Right
1
− 6, 9 − 10
Left
1
− 10, 6 − 9
Right side Up
1
− 6, 3 − 9
Down
1
− 3, 6 − 9
Right
1
− 6, 2 − 9
Left
1
− 2, 6 − 9
AC000444
OUTSIDE MIRROR
TSB Revision
EXTERIOR
51-43
HEATING ELEMENT FUNCTION CHECK
For vehicles with heated door mirrors, check that there is conti-
nuity between terminals (3) and (7).
AC000443
SPECIFICATIONS
TSB Revision
EXTERIOR
51-44
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1511015300310
SERVICE SPECIFICATIONS
M1511000300240
SEALANTS AND ADHESIVES
M1511000500482
ITEM
SPECIFICATION
Rear deflector
Rear deflector bolt
5.0
± 1.0 N⋅m (44 ± 9 in-lb)
Rear deflector nut
5.0
± 1.0 N⋅m (44 ± 9 in-lb)
Side step <Type A>
Side step assembly nut
11
± 2 N⋅m (98 ± 17 in-lb)
Side step assembly bolt
60
± 5 N⋅m (45 ± 3 ft-lb)
Side step <Type B>
Side step assembly bolt
60
± 5 N⋅m (45 ± 3 ft-lb)
Windshield wiper and washer
Wiper arm and blade assembly nut
24
± 3 N⋅m (18 ± 2 ft-lb)
Wiper link assembly bolt
4.9
± 1.0 N⋅m (44 ± 8 in-lb)
Wiper motor assembly bolt
8.9
± 1.9 N⋅m (79 ± 17 in-lb)
Inlet assembly bolt
4.9
± 0.7 N⋅m (44 ± 6 in-lb)
Washer tank assembly bolt
4.9
± 0.7 N⋅m (44 ± 6 in-lb)
Rear wiper and washer
Wiper arm and blade assembly nut
8.0
± 1.2 N⋅m (71 ± 10 in-lb)
Wiper motor assembly bolt
4.9
± 0.7 N⋅m (44 ± 6 in-lb)
Washer tank assembly bolt
4.9
± 0.7 N⋅m (44 ± 6 in-lb)
Washer motor bolt
4.9
± 0.7 N⋅m (44 ± 6 in-lb)
ITEM
STANDARD VALUE
Windshield wiper blade position
installation mm (in)
Driver's side
20
− 30 (0.8 − 1.2)
Passenger's side
25
− 35 (1.0 − 1.4)
Rear wiper blade position installation mm (in)
25
− 35 (1.0 − 1.4)
ITEM
SPECIFICATION
Front wheel cut molding
Adhesive tape: Double-sided tape 4.0 mm (0.16 in) width and 1.2 mm
(0.05 in) thickness and 30.0 mm (1.18 in) width and 0.8 mm (0.03 in)
thickness and 35.0 mm (1.38 in) width and 1.2 mm (0.05 in) thickness
Front door molding
Adhesive tape: Double-sided tape 4.0 mm (0.16 in) width and 1.2 mm
(0.05 in) thickness
Front door core (front door
molding side, front door side)
Adhesive tape: Double-sided tape 5.0 mm (0.20 in) width and 2.0 mm
(0.08 in) thickness
Rear door molding
Adhesive tape: Double-sided tape 4.0 mm (0.16 in) width and 1.2 mm
(0.05 in) thickness and 24.0 mm (0.95 in) width and 1.2 mm (0.05 in)
thickness
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст