Mitsubishi Montero (2004+). Manual — part 668
HOOD
TSB Revision
BODY
42-3
HOOD
HOOD DIAGNOSIS
INTRODUCTION TO HOOD DIAGNOSIS
M1421005800040
Wind noise at the hood may be caused by improper
hood adjustment.
HOOD DIAGNOSTIC TROUBLESHOOTING STRATEGY
M1421005900036
Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find a
hood fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by following the Symptom
Chart.
4. Verify malfunction is eliminated.
SYMPTOM CHART
M1421006000337
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Difficult Locking and Unlocking
DIAGNOSIS
STEP 1. Check the release cable routing
condition.
Q: Is the release cable routing condition good?
YES :
Go to Step 2.
NO :
Repair the release cable, then go to Step 4.
STEP 2. Check the engagement of the hood latch
and hood striker.
Q: Are the hood latch and hood striker engaged
correctly?
YES :
Go to Step 3.
NO :
Adjust the hood latch (Refer to
Then go to Step 4.
STEP 3. Check for proper lubrication of release
cable.
Q: Is the release cable properly lubricated?
YES :
Go to Step 4.
NO :
Lubricate, then go to Step 4.
STEP 4. Retest the system.
Q: Does the hood lock operate easily?
YES :
The procedure is complete.
NO :
Return to Step 1.
SYMPTOM
INSPECTION PROCEDURE
REFERENCE PAGE
Difficult locking and unlocking
1
Uneven body clearance
2
Uneven height
3
HOOD
TSB Revision
BODY
42-4
INSPECTION PROCEDURE 2: Uneven Body Clearance
DIAGNOSIS
STEP 1. Check the hood installation condition.
Q: Is the hood installation in good condition?
YES :
Go to Step 2.
NO :
). Then go
to Step 2.
STEP 2. Retest the system.
Q: Is the clearance with the body even?
YES :
The procedure is complete.
NO :
Return to Step 1.
INSPECTION PROCEDURE 3: Uneven Height
DIAGNOSIS
STEP 1. Check the hood bumper height.
Q: Is the hood bumper height proper?
YES :
Go to Step 2.
NO :
Adjust the hood bumper (Refer to
Then go to Step2.
STEP 2. Retest the system.
Q: Are the hood and body height even?
YES :
The procedure is complete.
NO :
Return to Step 1.
HOOD
TSB Revision
BODY
42-5
HOOD
REMOVAL AND INSTALLATION
M1421001600226
ACX01958
A18C0021
AW0381AU
22 ± 4 N·m
16 ± 3 ft-lb
9.0 ± 2.0 N·m
79 ± 18 in-lb
2
1
3
4
5
6
7
8
9
7
7
5
7
5.0 ± 1.0 N·m
44 ± 9 in-lb
1
2
AB
10
HOOD LATCH REMOVAL STEPS
• RADIATOR GRILL (REFER TO
GROUP 51
− FRONT
BUMPER
)
1. HOOD LATCH
HOOD LOCK RELEASE CABLE
REMOVAL STEPS
2. HOOD LOCK RELEASE HANDLE
3. HOOD LOCK RELEASE CABLE
HOOD AND HOOD HINGE
REMOVAL STEPS
4. HOOD INSULATOR
5. HOOD WEATHERSTRIP
• WASHER HOSE (REFER TO
GROUP 51
− WINDSHIELD WIPER
AND WASHER
)
6. HOOD
7. BUMPER A
8. HOOD SUPPORT ROD
• FRONT DECK GARNISH (REFER
TO GROUP 51
− WINDSHIELD
WIPER AND WASHER
9. HOOD HINGE
10. HOOD SWITCH
HOOD AND HOOD HINGE
REMOVAL STEPS (Continued)
HOOD
TSB Revision
BODY
42-6
ACX00459
AC203663
AX0385CA
AW0382AL
AX0423CA
AX0424CA
ADJUSTMENT OF CLEARANCE AROUND HOOD
ADJUSTMENT OF HOOD AND
HOOD STRIKER ENGAGEMENT
SECTION A – A
SECTION B – B
6
7
6
7
B
B
A
A
15 ± 0.5 mm
0.59 ± 0.02 in
20 ± 0.5 mm
0.78 ± 0.02 in
CLIP POSITIONS
SECTION A – A
A
A
6
CLIP
4
4
6
: CLIP POSITION
AB
ADJUSTMENT OF HEIGHT AROUND HOOD
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст