Mitsubishi Montero (2004+). Manual — part 692
SYMPTOM CHART
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-25
Headlight and taillight
General description concerning headlight
and taillight function
−
Taillights do not illuminate.
J-1
Headlights (low-beam) do not illuminate.
J-2
Headlights (high-beam) do not illuminate.
J-3
Headlights do not illuminate when the
passing switch is operated.
J-4
Headlights do not illuminate when the
lighting switch is at "TAIL," and "PASSING"
position, but illuminate at low-beam when
the switch is at "HEAD" position. At this
position, the headlights cannot be changed
into high beam by operating the dimmer
switch.
J-5
Any of taillights, position lights or license
plate light does not illuminate.
J-6
One of the headlights does not illuminate.
J-7
The high-beam Indicator Light does not
Illuminate.
J-8
Headlight automatic shutdown function
does not work normally.
J-9
Headlight dimmer switch automatic
resetting function does not work normally.
J-10
Daytime running light function does not
work normally. <vehicles for Canada>
J-11
Flasher timer
General description concerning the flasher
timer function
−
Turn-signal lights do not flash when the
turn signal light switch is operated.
K-1
Hazard warning lights do not illuminate.
K-2
One of the turn-signal lights do not
illuminate.
K-3
Fog light
General description concerning the fog
light function
−
Fog lights do not illuminate when the fog
light switch is operated.
L-1
Fog lights do not go out when the
headlights (low-beam) are turned off while
the fog lights are on.
L-2
One of the fog lights does not illuminate.
L-3
SYSTEM
SYMPTOM
INSPECTION
PROCEDURE
REFERENCE
PAGE
SYMPTOM CHART
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-26
Interior light
General description concerning the interior
light function
−
The dome light do not illuminate or go out
normally.
M-1
Dome light dimming function does not work
normally.
M-2
The ignition key hole illumination light does
not illuminate or go out normally.
M-3
Theft-alarm system
General description concerning the
theft-alarm system
−
Theft-alarm system is not armed
(theft-alarm indicator light does not
illuminate).
N-1
Horn does not sound when the theft-alarm
system is triggered.
N-2
Headlights (high-beam) do not flash when
the theft-alarm system is triggered.
N-3
Panic alarm function does not work.
N-4
SYSTEM
SYMPTOM
INSPECTION
PROCEDURE
REFERENCE
PAGE
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-27
SYMPTOM PROCEDURES
INSPECTION PROCEDURE A-1: Communication with the SWS monitor kit is not possible.
.
TECHNICAL DESCRIPTION (COMMENT)
The SWS monitor kit may be connected improperly.
Scan Tool Communication and ETACS-ECU Ground Circuit
AC204170
CONNECTORS : D-02, D-117, D-118
BH
D-118(B)
D-02
D-117
AC204173
CONNECTORS : D-209, D-220
D-208
D-220
AT
AC204174
CONNECTORS : D-222, D-224
D-224(B)
AH
D-222
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-28
.
TROUBLESHOOTING HINTS
• The SWS monitor body (I/F cartridge) may be
defective
• The SWS monitor harness may be defective
• The ETACS-ECU may be defective
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
STEP 1. Verify SWS monitor kit MB991862 for proper
connection.
Q: Is SWS monitor kit MB991862 connected with the
column switch properly?
YES : Go to Step 2.
NO : Connect SWS monitor kit MB991862 to the column
switch securely.
STEP 2. Verify the power supply circuit to the ETACS-ECU.
Q: Does the system communicate with scan tool
MB991502 when the ignition switch is turned to the
"ON" position?
YES : Go to Step 3.
NO : Refer to Inspection Procedure A-3 "Communication
with the ETACS-ECU is not possible
."
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст