Mitsubishi Montero (2004+). Manual — part 770
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-337
STEP 39. Check license plate light assembly connector
I-04 for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is license plate light assembly connector I-04 in good
condition?
YES : Go to Step 40.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the license plate lights illuminate
normally.
STEP 40. Check the ground circuit to the license plate
light. Test at license plate light assembly connector I-04.
(1) Disconnect license plate light assembly connector I-04 and
measure the resistance available at the wiring harness side
of the connector.
(2) Measure the resistance value between terminal 1 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 42.
NO : Go to Step 41.
STEP 41. Check the wiring harness between license plate
light assembly connector I-04 (terminal 1) and ground.
Q: Is the wiring harness between license plate light
assembly connector I-04 (terminal 1) and ground in
good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the license plate lights illuminate normally.
AC204182
CONNECTOR : I-04
AB
HARNESS SIDE
1
2
AC204182
CONNECTOR : I-04
AB
HARNESS SIDE
1
2
AC100262
1
2
AB
CONNECTOR I-04
(HARNESS SIDE)
AC204182
CONNECTOR : I-04
AB
HARNESS SIDE
1
2
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-338
STEP 42. Check front-ECU connector A-07X for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is front-ECU connector A-07X in good condition?
YES : Go to Step 43.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the license plate lights illuminate
normally.
STEP 43. Check the wiring harness between license plate
light assembly connector I-04 (terminal 2) and front-ECU
connector A-07X (terminal 8).
AC204183
CONNECTOR : A-07X
AB
2 1
3
4
6
7
8
9
5
11 10
RELAY BOX SIDE
AC204183
CONNECTOR : A-07X
AB
2 1
3
4
6
7
8
9
5
11 10
RELAY BOX SIDE
AC204182
CONNECTOR : I-04
AB
HARNESS SIDE
1
2
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-339
NOTE: Also check intermediate connectors D-28, D-111 and
G-10 for loose, corroded, or damaged terminals, or terminals
pushed back in the connector. If intermediate connector D-28,
D-111 or G-10 is damaged, repair or replace the damaged com-
ponent(s) as described in GROUP 00E, Harness Connector
Inspection
.
Q: Is the wiring harness between license plate light
assembly connector I-04 (terminal 2) and front-ECU
connector A-07X (terminal 8) in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the license plate lights illuminate normally.
STEP 44. Check the side marker light bulb (LH).
(1) Remove the side marker light bulb (LH).
(2) Verify that the side marker light bulb (LH) is not damaged or
burned out.
Q: Is the side marker light bulb (LH) in good condition?
YES : Go to Step 45.
NO : Replace the side marker light bulb (LH). Verify that
the side marker lights (LH) illuminates normally.
AC204170
CONNECTOR : D-28
AI
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
AC204171
CONNECTOR : D-111
BH
9
8
6 7
5
3 4
20
32
21
33
43
17 18
30
41
16
29
28
39 40
13
25
12
24
35 36
14
26
37
15
27
38
19
31
42
1
10
22
2
11
23
34
AC204179
CONNECTOR : G-10
AD
4
10
8
7
3
9
5
1
6
2
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-340
STEP 45. Check side marker light (LH) connector G-02 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is side marker light (LH) connector G-02 in good
condition?
YES : Go to Step 46.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the side marker lights (LH)
illuminates normally.
STEP 46. Check the ground circuit to the side marker light
(LH). Test at side marker light (LH) connector G-02.
(1) Disconnect side marker light (LH) connector G-02 and
measure the resistance available at the wiring harness side
of the connector.
(2) Measure the resistance value between terminal 4 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 48.
NO : Go to Step 47.
STEP 47. Check the wiring harness between side marker
light (LH) connector G-02 (terminal 4) and ground.
Q: Is the wiring harness between side marker light (LH)
connector G-02 (terminal 4) and ground in good
condition?
YES : Replace the side marker light socket. Verify that the
side marker light (LH) illuminates normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the side marker light (LH) illuminates normally.
AC204179
CONNECTOR : G-02
AB
HARNESS SIDE
G-02(B)
G-02(B)
1
4
2
3
5
6
AC204179
CONNECTOR : G-02
AB
HARNESS SIDE
G-02(B)
G-02(B)
1
4
2
3
5
6
AC100256
1
4
2
3
5
6
AB
CONNECTOR G-02
(HARNESS SIDE)
AC204179
CONNECTOR : G-02
AB
HARNESS SIDE
G-02(B)
G-02(B)
1
4
2
3
5
6
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст