Mitsubishi Montero (2004+). Manual — part 529
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-85
(3) Measure the distance from the center line of the vehicle
to the center of each fog light. Transfer the measurement
to the screen. Vertical tape or mark on the screen with
reference to the center line of each fog light bulb.
FOG LIGHT ADJUSTMENT
1. Check if the beam shining onto the screen is at the standard
value.
Standard value:
(Vertical direction): Top of the hot zone should be
101 mm (4.0 inches) below the fog light center
(equivalent to the fog light beam angle of 0.76
°).
(Horizontal direction): Parallel to direction of vehicle
travel
Limit:
(Vertical direction): Top of the hot zone should be
152 mm (6.0 inches) below the fog light center
(equivalent to the fog light beam angle of 1.14
°).
2. If the value is outside the standard value range, adjust using
the adjusting screw.
NOTE: The horizontal direction is non-adjustable. If devia-
tion of the light beam axis exceeds the standard value,
check that the mounting location or some other points are
not faulty.
AC100547
HEIGHT OF FOG
LIGHT CENTER
VERTICAL CENTER LINE
AHEAD OF FOG LIGHT
UPPER MOST LEVEL
OF HOT ZONE
HOT ZONE
mm (in)
AB
152 (6.0)
101 (4.0)
598 (23.5)
598 (23.5)
AC204113 AB
AC204113
ADJUSTING SCREW
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-86
FOG LIGHT
REMOVAL AND INSTALLATION
M1542001500157
AC204148
ACX01472
ACX01404
ACX01477
AB
6
7
1
2
3
4
5
1. ETACS-ECU
2. FRONT-ECU
FOG LIGHT SWITCH REMOVAL
STEPS
3. INSTRUMENT PANEL SIDE COVER
>>A<<
4. AIR OUTLET ASSEMBLY
5. FOG LIGHT SWITCH
FOG LIGHT REMOVAL STEPS
6. FOG RIGHT
<<A>>
7. BULB
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-87
REMOVAL SERVICE POINT
.
<<A>> BULB REMOVAL
CAUTION
• Use the specified genuine part when replacing the bulb.
• Do not touch the glass portion of bulb with bare hand
or dirty gloves. Should the glass portion be spoiled,
remove the soil as soon as possible using alcohol or
thinner and let it dry before mounting.
Turn the bulb assembly left to remove it.
INSTALLATION SERVICE POINT
.
>>A<< AIR OUTLET ASSEMBLY INSTALLATION
1. Insert the hand from the mounting hole of the instrument
panel side cover to hold and fix the fog light switch cover by
the hand.
2. While inter fitting the air outlet assembly duct, connect the
fog light switch to the connector.
NOTE: After fitting, check that the open/close damper knob of
the air outlet can be operated normally.
INSPECTION
M1542011200072
FOG LIGHT SWITCH CONTINUITY CHECK
AC204147AB
ACX01405
AB
SWITCH POSITION TESTER
CONNECTION
SPECIFIED
CONDITION
ON
1
− 2
Less than 2 ohms
OFF
1
− 2
Open circuit
ACX00797AB
REAR COMBINATION LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-88
FOG LIGHT RELAY CHECK
REAR COMBINATION LIGHT
LIGHTING SYSTEM DIAGNOSIS
M1542000700501
The taillights and turn-signal lights are controlled by
the Simplified Wiring System (SWS). For trouble-
shooting, refer to GROUP 54B, SWS Diagnosis
−
Symptom Chart
REAR COMBINATION LIGHT
REMOVAL AND INSTALLATION
M1542003900526
WARNING
•
Before removal of the air bag module, refer to GROUP 52B, SRS Service Precautions
(
) and Air Bag Module and Clock Spring (
•
When removing and installing the steering wheel, do not let it bump against the air bag
module.
BATTERY VOLTAGE
TESTER
CONNECTION
SPECIFIED
CONDITION
Not applied
4
− 5
Open circuit
• Connect terminal 3 to the
positive battery terminal
• Connect terminal 1 to the
negative battery terminal
4
− 5
Less than 2
ohms
1 2 3
4
5
4
5
1
2
ACX01668
4
3
1
AC
BATTERY
FOG LIGHT RELAY
ACX01803AC
1
2
3
BATTERY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст