Mitsubishi Outlander GS45X. Manual — part 1043
SEAT ASSEMBLY
TSB Revision
INTERIOR
52A-21
DISASSEMBLY SERVICE POINTS
.
<<A>> HEADREST GUIDE REMOVAL
Peel of the front seatback cover and pad to access the head-
restraint guides. Pull off the guides upwards while pushing the
tabs (arrows) as shown.
.
<<B>> SEAT CUSHION FRAME ASSEMBLY
REMOVAL
For the vehicles with side air bag, do not remove the side air
bag module from the frame.
5.
Inner seat belt
6.
Heated seat switch cover <vehicle
with heated seat>
7.
Heated seat switch <vehicle with
heated seat>
8.
Seat back assembly
<<
A
>>
9.
Headrest guide
10. Seat back cover
11. Seat back pad
12. Hinge cover inner
13. Seat cushion cover
14. Seat cushion pad
15. Seat slide adjuster lever
<<
B
>>
16. Seat cushion frame assembly
Disassembly steps (Continued)
AC205342
SEAT ASSEMBLY
TSB Revision
INTERIOR
52A-22
INSPECTION
M1522001600442
INSPECTION OF THE HEATED SEAT RELAY FOR
CONTINUITY
INSPECTION OF THE HEATED SEAT SWITCH
FOR CONTINUITY
Inspect the heated seat switch for continuity.
Battery voltage
Terminal
number
Normal value
At no energization
3
− 4
No continuity
At energization
[terminal 2 (+)
−
terminal 1 (
−)]
Continuity exists
(2
Ω or less).
AC803281
1
2
3
4
AB
Heated seat relay
Switch
position
Terminal
number
Normal
value
Note
HI
1
− 2
Continuit
y exists
(2
Ω or
less).
2(+)
− 6(-)
Indicator
3
− 4
Illumination
OFF
3
− 4
Illumination
LOW
2
− 5
Continuit
y exists
(2
Ω or
less).
2(+)
− 6(-)
Indicator
3
− 4
Illumination
AC803282AB
SEAT ASSEMBLY
TSB Revision
INTERIOR
52A-23
SEAT CUSHION HEATER INSPECTION
Measure the resistance between the terminals.
Standard value: At room temperature 20
°C (68 °F)
SEAT BACK HEATER INSPECTION
Measure the resistance between the terminals.
Standard value: At room temperature 20
°C (68 °F)
Terminal number
Standard value
Seat cushion heater
(Terminal No.1)
− Seatback
heater (Terminal No.1)
0.198 to 0.242
Ω
Seat cushion heater
(Terminal No.3)
− Seatback
heater (Terminal No.1)
4.13 to 5.03
Ω
<Thermostat: ON>
3.93 to 4.79
Ω
<Thermostat: OFF>
AC803284AC
Seat cushion
heater
Seatback
heater
Terminal number
Standard value
1
− 2
4.79 to 5.85
Ω
AC803277AB
SEAT ASSEMBLY
TSB Revision
INTERIOR
52A-24
SECOND SEAT ASSEMBLY
SECOND SEAT ADJUSTMENT
M1522005400031
.
1. Check that the automatic tumble mechanism works.
2. If the slide lock release is late, remove the reclining adjuster
cover, and move the clamp position of the slide lock release
cable for the automatic tumble mechanism on the side of the
seat from the second recess to the first recess to adjust the
slide lock release timing.
3. Check again that the automatic tumble mechanism works. If
the slide lock timing is still late after the adjustment, replace
the slide lock release cable for the automatic tumble
mechanism.
4. If the slide lock timing is still late after the slide lock release
cable for the automatic tumble mechanism is replaced,
replace the seat.
5. If the automatic tumble mechanism is normal, lock the
sliding and turn up the seat cushion pad. Then, check that
the clearance between the slide lock claw and the second
seat folding adjuster is approximately 3 mm(0.1in).
AC611163AB
Reclining
adjuster cover
A
AC611188
Slide lock release cable
for automatic tumble
mechanism
Change the
installation
position of
the clamp (yellow)
to the first recess.
AB
View A
AC611007
AC610995
AC611189 AB
Second seat
folding adjuster
Claw on slide lock
Clearance between
the second seat
folding adjuster
and the claw.
Approx. 3mm
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст