Mitsubishi Outlander GS45X. Manual — part 1630
DIAGNOSIS
TSB Revision
CVT
23A-77
.
DIAGNOSTIC FUNCTION
TCM detects that the paddle shift UP switch is stuck
to ON.
.
JUDGEMENT CRITERIA
When the paddle shift UP switch being ON consecu-
tively for 60 seconds is detected.
.
PROBABLE CAUSES
• Malfunction of paddle shift switch
• Damaged wiring harness and connectors
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
STEP 1. M.U.T.-III data list
Item 54: Paddle switch (up)
OK: The service data changes in response to the pad-
dle shift operation.
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Go to Step 2.
STEP 2. Check the following connector:
• C-38 TCM connector
• C-208 paddle shift switch connector
• C-34 intermediate connector
Check the terminals for a contact status problem and internal
short circuit.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Repair the damaged connector.
STEP 3. Paddle shift switch single unit check
Refer to
.
Q: Is the check result normal?
YES : Go to Step 4.
NO : Replace the paddle shift switch.
STEP 4. Check for short to ground in the wiring harness
between the TCM connector and the paddle shift switch
connector
Between C-38 TCM connector (terminal No.22) and C-208
paddle shift switch connector (terminal No.1)
Q: Is the check result normal?
YES : Go to Step 5.
NO : Repair the wiring harness.
STEP 5. Symptom recheck after erasing diagnosis code
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Replace TCM.
DIAGNOSIS
TSB Revision
CVT
23A-78
DTC P0816: Malfunction of Paddle Shift Down Switch
.
PADDLE SHIFT SWITCH SYSTEM
CIRCUIT
Refer to
.
DIAGNOSTIC FUNCTION
TCM detects that the paddle shift DOWN switch is
stuck to ON.
.
JUDGEMENT CRITERIA
When the paddle shift DOWN switch being ON con-
secutively for 60 seconds is detected.
.
PROBABLE CAUSES
• Malfunction of paddle shift switch
• Damaged wiring harness and connectors
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
STEP 1. M.U.T.-III data list
Item 55: Paddle switch (down)
OK: The service data changes in response to the pad-
dle shift operation.
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Go to Step 2.
STEP 2. Check the following connector:
• C-38 TCM connector
• C-208 paddle shift switch connector
Check the terminals for a contact status problem and internal
short circuit.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Repair the damaged connector.
STEP 3. Paddle shift switch single unit check
Refer to
.
Q: Is the check result normal?
YES : Go to Step 4.
NO : Replace the paddle shift switch.
STEP 4. Check for short to ground in the wiring harness
between the TCM connector and the paddle shift switch
connector
Between C-38 TCM connector (terminal No.21) and C-208
paddle shift switch connector (terminal No.3)
Q: Is the check result normal?
YES : Go to Step 5.
NO : Repair the wiring harness.
STEP 5. Symptom recheck after erasing diagnosis code
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Replace TCM.
DIAGNOSIS
TSB Revision
CVT
23A-79
DTC P0826: Malfunction of Shift Switch Assembly
SHIFT
SWITCH
SPORT
MODE
AUTO
MODE
SELECT
SWITCH
SELECTOR
LEVER
ASSEMBLY
TRANSAXLE
CONTROL MODULE
Shift switch assembly system circuit
ACA03154
AC703257
Connector: C-24
AB
AC702815
Connector: C-33
AB
AC703253
Connector: C-37
Brake pedal
AC
DIAGNOSIS
TSB Revision
CVT
23A-80
.
DIAGNOSTIC FUNCTION
TCM detects the UP/DOWN operation of the shift
switch assembly. TCM determines that the malfunc-
tion is present if an abnormal value is input.
.
JUDGEMENT CRITERIA
Input to the shift switch assembly remains abnormal
for 1 second.
.
PROBABLE CAUSES
• Malfunction of selector lever assembly (Faulty
shift switch assembly)
• Damaged wiring harness and connectors
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
STEP 1. M.U.T.-III data list
• Item 52: Select switch (up)
• Item 53: Select switch (down)
(Refer to Data List Reference Table
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Go to Step 2.
STEP 2. Check shift switch assembly
Refer to
.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Replace the selector lever assembly.
STEP 3. Check the following connector:
• C-37 TCM connector
• C-24 selector lever assembly connector
Check the terminals for a contact status problem and internal
short circuit.
Q: Is the check result normal?
YES : Go to Step 4.
NO : Repair the defective connector.
STEP 4. Check for open circuit and short to ground in the
wiring harness between the TCM connector and the
selector lever assembly.
• Between C-37 TCM connector (terminal No.35) and C-24
selector lever assembly connector (terminal No.8)
• Between C-37 TCM connector (terminal No.43) and C-24
selector lever assembly connector (terminal No.10)
• Between C-37 TCM connector (terminal No.44) and C-24
selector lever assembly connector (terminal No.9)
Q: Is the check result normal?
YES : Go to Step 5.
NO : Repair the wiring harness.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст