Mitsubishi Outlander GS45X. Manual — part 1631
DIAGNOSIS
TSB Revision
CVT
23A-81
STEP 5. Check for open circuit in the wiring harness
between the selector lever assembly connector and the
body ground
Between C-24 selector lever assembly connector (terminal
No.6) and body ground
Q: Is the check result normal?
YES : Go to Step 6.
NO : Repair the wiring harness.
STEP 6. Symptom recheck after erasing diagnosis code
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Replace TCM.
DTC P0840: Malfunction of Secondary Pressure Sensor
SECONDARY
PRESSURE
SENSOR
AC901224
CVT
ASSEMBLY
TRANSAXLE
CONTROL MODULE
Secondary pressure sensor system circuit
AC709490
Connector: A-12
AB
AC709493
AD
Connector: B-125
B-125 (B)
DIAGNOSIS
TSB Revision
CVT
23A-82
.
DIAGNOSTIC FUNCTION
TCM conducts fault detection by monitoring the out-
put voltage of the secondary pressure sensor.
.
DESCRIPTIONS OF MONITOR METHODS
• The status with the fluid temperature of −20°C
(
−4°F) or more and with the secondary pressure
sensor voltage of 4.69 volts or more continues for
5 seconds.
• The status with the fluid temperature of −20°C
(
−4°F) or more and with the secondary pressure
sensor voltage of 0.09 volts or less continues for
5 seconds.
.
MONITOR EXECUTION
• Continuous
.
MONITOR EXECUTION CONDITIONS
(OTHER MONITOR AND SENSOR)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• P0746: Abnormality in hydraulic control system
function
• P0841: Abnormality in line pressure sensor func-
tion
• P0868: Secondary pressure drop
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
AC703253
Connector: C-37
Brake pedal
AC
DIAGNOSIS
TSB Revision
CVT
23A-83
LOGIC FLOW CHARTS (Monitor Sequence)
.
AC609343
START
Yes
Yes
No
Continuous failure for 5 sec
No
No
Yes
Good
Malfunction
END
Yes
Yes
Yes
No
No
Secondary pressure
sensor voltage 4.69 mA
Secondary pressure
sensor voltage 0.09 V
No
Continuous failure for 5 sec
Transmission fluid > -20˚C (-4˚F)
Transmission fluid > -20˚C (-4˚F)
V
AC
DIAGNOSIS
TSB Revision
CVT
23A-84
DTC SET CONDITIONS
JUDGMENT CRITERIA
• Secondary pressure sensor voltage [transmission
fluid temperature: more than
−20°C (−4°F)]: 4.69
volts or more. (5 seconds)
• Secondary pressure sensor voltage [transmission
fluid temperature: more than
−20°C (−4°F)]: 0.09
volt or less. (5 seconds)
.
OBD-II DRIVE CYCLE PATTERN
All the conditions below continue for 6 seconds.
• Transmission range switch: D
• Vehicle speed: 10 km/h (6.2 mph) or more
• Throttle position: 1/8 or more
• Engine speed: 450 r/min or more
• Transmission fluid temperature: 20°C (68°F) or
more.
• Transmission fluid temperature: 99°C (210°F) or
more.
.
PROBABLE CAUSES
• Malfunction of valve body assembly (Faulty sec-
ondary pressure sensor)
• Damaged wiring harness and connectors
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
STEP 1. M.U.T.-III data list
• Item 4: Secondary pressure sensor signal (Refer to Data
List Reference Table
Q: Is the check result normal?
YES : Intermittent malfunction
NO : Go to Step 2.
STEP 2. Check the following connector:
• B-125 CVT assembly connector
• C-37 TCM connector
• A-12 Intermediate connector
Check the terminals for a contact status problem and internal
short circuit.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Repair the defective connector.
STEP 3. Check for open circuit and short to ground in the
wiring harness between the TCM connector and the CVT
assembly connector.
• Between C-37 TCM connector (terminal No.39) and B-125
CVT assembly connector (terminal No.7)
• Between C-37 TCM connector (terminal No.48) and B-125
CVT assembly connector (terminal No.19)
• Between C-37 TCM connector (terminal No.49) and B-125
CVT assembly connector (terminal No.5)
Q: Is the check result normal?
YES : Go to Step 4.
NO : Repair the wiring harness.
STEP 4. Symptom recheck after replacing the valve body
assembly
Q: Is the check result normal?
YES : The procedure is complete.
NO : Replace TCM.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст