Mitsubishi Outlander GS45X. Manual — part 1375
OUTSIDE MIRROR
TSB Revision
EXTERIOR
51-123
REMOVAL SERVICE POINTS
.
<<A>> MIRROR REMOVAL
CAUTION
The tab of the mirror is prone to breakage when working in
cold temperatures. Always use a hair drier or the like to
warm up the mirror tab and its periphery to 20
°C (68°F) or
higher prior to works. When the mirror is heated too
quickly from its cold state, it may be broken.
1. Slant the mirror upward with your hands. Then insert a
flat-tipped screwdriver wrapped with protective tape
between the pivot plate and mirror. Now pry off the mirror
claws and release the lower side of the mirror as shown in
the illustration.
2. Release the upper side of the mirror claws while pulling out
the mirror.
3. Disconnect the connectors of the heated mirror.
.
<<B>> DOOR MIRROR OUTER COVER REMOVAL
<TYPE 1>
1. Remove the mirror (Refer to the step A of the REMOVAL
SERVICE POINTS).
2. Remove the door mirror outer cover claws as shown in the
figure and remove the outer cover from the door mirror
housing.
NOTE: If claw(s) are difficult to disengage, remove the actuator
mounting screws to release the actuator and disengage the
claws.
.
AC900156
AC302282
A
A
AB
Section A – A
Claw positions
Claw
Claw
Claw
Pivot plate
Mirror
Mirror
Flat-tipped screwdriver
Flat-tipped
screwdriver
Flat-tipped screwdriver
Protective tape
AC506999AE
: Claw positions
Type 1
Actuator
OUTSIDE MIRROR
TSB Revision
EXTERIOR
51-124
<<C>> DOOR MIRROR OUTER COVER REMOVAL
<TYPE 2>
1. Remove the mirror (Refer to the step A of the REMOVAL
SERVICE POINTS).
CAUTION
When installing, always use new Torx screws.
2. Remove the 3 Torx screws connecting the mirror base and
mirror housing.
3. Pull out the mirror housing from the mirror base; taking care
not to damage the door mirror harness and connector.
CAUTION
When installing, always use new Torx screw.
4. Remove the Torx screw connecting the plate and mirror
housing.
5. Remove the screw connecting the mirror housing and
actuator lower part.
6. Remove the 2 screws connecting the actuator and mirror
housing.
7. Slide the actuator and disengage the door mirror outer cover
claws as shown in the figure. Remove the outer cover from
the door mirror housing.
AC900162
N
N
N
Mirror housing
Mirror base
AB
AC900163
N
Mirror housing
Plate
AB
Mirror base
AC900173
Mirror housing
AB
Screw
AC900161AB
: Claw positions
Screw
Screw
Actuator
OUTSIDE MIRROR
TSB Revision
EXTERIOR
51-125
INSTALLATION SERVICE POINT
.
>>A<< DOOR MIRROR OUTER COVER INSTAL-
LATION
CAUTION
Tap the claw positions to confirm that they are engaged
and the door mirror outer cover is installed securely.
Install the door mirror outer cover by engaging the claws as
shown in the figure.
AC506999
Type 1
AG
: Claw positions
AC900161AC
: Claw positions
Type 2
OUTSIDE MIRROR
TSB Revision
EXTERIOR
51-126
INSPECTION
M1511019103447
DOOR MIRROR ASSEMBLY OPERATION CHECK
Remove the door trim, and then connect the battery to the door
mirror assembly connector to check that the door mirror oper-
ates.
REMOTE CONTROLLED MIRROR SWITCH
CONTINUITY CHECK
Battery connection
Operation
direction
• Connect terminal 13 to the negative
battery terminal.
• Connect terminal 4 to the positive
battery terminal.
Up
• Connect terminal 13 to the positive
battery terminal.
• Connect terminal 4 to the negative
battery terminal.
Down
• Connect terminal 13 to the negative
battery terminal.
• Connect terminal 12 to the positive
battery terminal.
Right
• Connect terminal 13 to the positive
battery terminal.
• Connect terminal 12 to the negative
battery terminal.
Left
AC900494AB
Switch position
Tester
connectio
n
Specified
condition
Left side
Up
1
− 6, 9 −
11
Continuity
(Less than
2
Ω)
Down
1
− 11, 6 −
9
Right
1
− 6, 9 −
10
Left
1
− 10, 6 −
9
Right side
Up
1
− 6, 3 − 9
Down
1
− 3, 6 − 9
Right
1
− 6, 2 − 9
Left
1
− 2, 6 − 9
AC005970
AC507009
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст