Mitsubishi Outlander GS45X. Manual — part 1373
OUTSIDE MIRROR
TSB Revision
EXTERIOR
51-115
.
CIRCUIT OPERATION
If either of the heated door mirror do not operate nor-
mally, it may be due to malfunctions in the heated
door mirror circuit or door mirror.
.
TROUBLESHOOTING HINTS
• Malfunction of the heated door mirror circuit
• Malfunction of the door mirror
• The wiring harness or connectors may have
loose, corroded or damaged terminals, or termi-
nals pushed back in the connector.
DIAGNOSIS
Required Special Tools:
• MB991223: Test Harness Set
STEP 1. Verify the operation of each heated door mirror.
Q: Which door mirror does not heat?
Door mirror (LH) : Go to Step 2.
Door mirror (RH) : Go to Step 8.
STEP 2. Check door mirror (LH) connector E-29 door
mirror assembly for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Is door mirror (LH) connector E-29 door mirror
assembly in good condition?
YES : Go to Step 3.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. And then check to see that the heater
function of the door mirror (LH) operates normally.
ACA02655 AG
C-306
Connector: C-306
AC605844
AZ
Connector: E-28
AC605845
BL
Connector: E-29
OUTSIDE MIRROR
TSB Revision
EXTERIOR
51-116
STEP 3. Check the heater of the door mirror (LH).
CAUTION
When relocating the car between locations of extremely
different temperatures (warm and cold), leave the car in a
location for a while to adapt to the temperature prior to
checking it.
Check to see that the resistance between terminal 1 and 2 of
the door mirror (LH) connector 9 of E-29 door mirror assembly.
• The resistance should be 7.2 ± 1.4 Ω at 25°C (77°F).
Q: Is the resistance normal?
YES : Go to Step 4.
NO : Replace the door mirror (LH). And then check to see
that the heater function of the door mirror (LH) is
operating normally.
STEP 4. Check the ground circuit between door mirror (LH)
connector E-29 door mirror assembly and ground for open
circuit. Measure the resistance at door mirror (LH)
connector E-29 door mirror assembly.
(1) Disconnect door mirror (LH) connector E-29 door mirror
assembly and check at the wiring harness side connector.
(2) Measure the resistance value between terminal 1 and
ground.
• The resistance should be 2Ω or less.
Q: Is the measured resistance 2
Ω or less?
YES : Go to Step 6.
NO : Go to Step 5.
STEP 5. Check the wiring harness between door mirror
(LH) connector E-29 door mirror assembly (terminal 1) and
ground.
NOTE: Also check intermediate connector C-126 for loose, cor-
roded or damaged terminals, or terminals pushed back in the
connector. If intermediate connector C-126 is damaged, repair
or replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between door mirror (LH)
connector E-29 door mirror assembly (terminal 1) and
ground in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged. Repair the
wiring harness as necessary. And then check to see
that the heater function of the door mirror (LH)
operates normally.
AC900574 AC
AC702473 AU
Harness side: E-29
OUTSIDE MIRROR
TSB Revision
EXTERIOR
51-117
STEP 6. Check rear window defogger relay connector
C-306 for loose, corroded or damaged terminal, or
terminals pushed back in the connector.
Q: Is rear window defogger relay connector C-306 in good
condition?
YES : Go to Step 7.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. And then check to see that the heater
function of the door mirror (LH) operates normally.
STEP 7. Check the wiring harness between door mirror
(LH) connector E-29 door mirror assembly (terminal 9) and
rear window defogger relay connector C-306 (terminal 3).
NOTE: Also check intermediate connector C-127 for loose, cor-
roded or damaged terminals, or terminals pushed back in the
connector. If intermediate connector C-127 is damaged, repair
or replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between door mirror (LH)
connector E-29 door mirror assembly (terminal 9) and
rear window defogger relay connector C-306 (terminal
3) in good condition?
YES : No action is necessary and testing is complete.
NO : Repair the wiring harness as necessary. And then
check to see that the heater function of the door
mirror (LH) operates normally.
STEP 8. Check the door mirror (RH) connector E-28 door
mirror assembly for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Is the door mirror (RH) connector E-28 door mirror
assembly in good condition?
YES : Go to Step 9.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. And then check to see that the heater
function of the door mirror (RH) operates normally.
OUTSIDE MIRROR
TSB Revision
EXTERIOR
51-118
STEP 9. Check the heater function of the door mirror (RH).
CAUTION
When relocating the car between locations of extremely
different temperatures (warm and cold), leave the car in a
location for a while to adapt to the temperature prior to
checking it.
Check to see that the resistance between terminal 1 and 2 of
the door mirror (RH) connector E-28 door mirror assembly.
• The resistance should be 7.2 ± 1.4 Ω at 25°C (77°F).
Q: Is the resistance normal?
YES : Go to Step 10.
NO : Replace the door mirror (RH). And then check to see
that the heater function of the door mirror (RH)
operates normally.
STEP 10. Check the ground circuit between door mirror
(RH) connector E-28 door mirror assembly and ground for
open circuit. Measure the resistance at door mirror (RH)
connector E-28 door mirror assembly.
(1) Disconnect door mirror (RH) connector E-28 door mirror
assembly, and check at the wiring harness side connector.
(2) Measure the resistance value between terminal 1 and
ground.
• The resistance should be 2Ω or less.
Q: Is the measured resistance 2
Ω or less?
YES : Go to Step 12.
NO : Go to Step 11.
STEP 11. Check the wiring harness between door mirror
(RH) connector E-28 door mirror assembly (terminal 1) and
ground.
NOTE: Also check intermediate connector C-112 for loose, cor-
roded or damaged terminals, or terminals pushed back in the
connector. If intermediate connector C-112 is damaged, repair
or replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between door mirror (RH)
connector E-28 door mirror assembly (terminal 1) and
ground in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged. Repair the
wiring harness as necessary. And then check to see
that the heater function of the door mirror (RH)
operates normally.
AC900574 AD
AC702473 AW
Harness side: E-28
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст