Mitsubishi Outlander GS45X. Manual — part 27

COMBINATION METER

TSB Revision

CHASSIS ELECTRICAL

54A-105

ON-VEHICLE SERVICE

SPEEDOMETER CHECK

M1540201400299

CAUTION

• Since the diagnostic trouble code may be stored in the

ABS-ECU or ASC-ECU when checking the speedometer
with speedometer tester, erase the diagnostic trouble
code.

• Do not accelerate or decelerate suddenly during servic-

ing work.

1. Adjust the pressure of tires to the specified level (Refer to

GROUP 31, On-vehicle Service

P.31-8

).

2. Where applicable, ensure that the TPMS warning light is not

illuminating or flashing.

3. <Vehicles with ASC> Press the ASC OFF switch for 3

seconds or more to stop the ASC operation.

CAUTION

Set a free-roller on the rear tire for AWD.
4. For FWD vehicles, set the vehicle onto a speedometer

tester and use wheel chocks to hold the rear wheels.

22

Illumination (

−) output

With daytime lighting control

1 V or less

With nighttime lighting control

In accordance with
the rheostat switch
operation, a pulse is
generated.

23

Illumination (+) output

With lighting control

Battery positive
voltage

24

Illumination (power supply) Always

Battery positive
voltage

Termina
l No.

Check item

Check conditions

Normal conditions

AC702851AB

<FWD>

Wheel chocks

COMBINATION METER

TSB Revision

CHASSIS ELECTRICAL

54A-106

5. For AWD vehicles, set the vehicle onto a speedometer

tester and place the rear wheels on a free roller.

6. To prevent the wheel from moving from side to side, attach

tension bars to the tie-down hook, and secure both ends to
anchor plates.

7. To prevent the vehicle from moving, attach a chain or wire to

the rear retraction hook, and make sure the end of the chain
or wire is secured.

8. Check if the speedometer indicator range is within the

standard values.

Standard value <Except vehicles for CANADA>:

Standard value <Vehicles for CANADA>:

9. If not within the standard value, check the tire size. If an

incorrect size of tire is used, replace it and check again. If
the tire size is correct, a defect may be present in
components and circuit between the ABS or ASC and the
combination meter. Check the following items.

Standard indication mph
(km/h)

Allowance range mph
(km/h)

10 (16)

8.5

− 11.5 (13.6 − 18.4)

25 (40)

23.5

− 26.5 (37.6 − 42.4)

50 (80)

48.5

− 51.5 (77.6 − 82.4)

75 (120)

73.5

− 76.5 (117.6 − 122.4)

100 (161)

98.5

− 102.5 (158.6 − 165.0)

125 (201)

123.5

− 127.5 (198.6 −

205.0)

standard indication km/h
(mph)

Allowance range km/h
(mph)

20 (12.4)

19

− 24 (11.8 − 14.9)

40 (24.8)

40

− 44 (24.8 − 27.3)

80 (49.7)

80

− 85 (49.7 − 52.8)

120 (74.6)

120.5

− 125.5 (74.9 − 78.0)

160 (99.4)

160.5

− 165.5 (99.7 − 102.8)

200 (124.3)

200.5

− 207.0 (124.6 −

128.6)

AC106044

Free roller

AN

<AWD>

AC001288

Front

AD

Puller

Anchor plate

COMBINATION METER

TSB Revision

CHASSIS ELECTRICAL

54A-107

• ABS or ASC (refer to GROUP 35B, Diagnosis

P.35B-15

<ABS> or GROUP 35C, Diagnosis

P.35C-18

<ASC>).

• Combination meter (refer to

P.54A-34

).

TACHOMETER CHECK

M1540201500230

When the actuator tests (item No.2) are performed using scan
tool MB991958, check that the tachometer indication error is
within the standard value.
NOTE: Values in ( ) indicates the reference value.

Standard value:

FUEL GAUGE UNIT CHECK

M1540201600408

VEHICLES FOR FWD

.

1. Remove the second seat (Refer to GROUP 52A

− Seat

Assembly

P.52A-25

).

2. Remove the floor inspection lid, and then remove the fuel

pump module (Refer to GROUP 13C

− Fuel Tank

P.13C-15

).

.

Engine speed r/min

Tachometer indicating
error r/min

600

550

− 650

(2,000)

(1,950

− 2,050)

3,000

2,950

− 3,050

(4,000)

(3,950

− 4,050)

5,000

4,950

− 5,050

6,000

5,950

− 6,050

(7,000)

(6,950

− 7,050)

(8,000)

(7,950

− 8,050)

COMBINATION METER

TSB Revision

CHASSIS ELECTRICAL

54A-108

NOMINAL RESISTANCE OF THE FUEL LEVEL
SENSOR

When float of the fuel level sensor is in stopper positions F and
E, ensure that resistance between the fuel level sensor terminal
and ground terminal is within the standard value.

Standard value:

When the float is moved slowly between stopper positions "F"
and "E", ensure that the resistance is smoothly changing.

.

FUEL LEVEL SENSOR FLOAT HEIGHT

When float is moved to contact the float arm on the stopper,
ensure that stopper positions "F" (height A) and "E" (height B)
are within the standard value.

Standard value:

VEHICLES FOR AWD

.

1. Remove the second seat (Refer to GROUP 52A

− Seat

Assembly

P.52A-25

).

2. Remove the floor inspection lid, and then remove the fuel

pump module and fuel level sensor (sub) (Refer to GROUP
13C

− Fuel Tank

P.13C-20

).

.

Float position

Gauge resistance value (

Ω)

Stopper position "F"

13.0

± 1.0

Stopper position "E"

120.0

± 1.0

AC609773AF

Ground

Fuel level sensor

Stopper position "F"

Stopper position "E"

Float position

Float height mm (in)

Stopper position "F" (height A)

201.6 (7.9)

Stopper position "E" (height B)

18.0 (0.7)

AC609774

B

A

AD

Stopper point "E"

Stopper point "F"