Mitsubishi Outlander GS45X. Manual — part 170
SATELLITE RADIO TUNER
TSB Revision
CHASSIS ELECTRICAL
54A-677
.
COMMENTS ON TROUBLE SYMPTOM
There may be a failure in the wiring harness from the
satellite radio tuner to the radio and CD player <vehi-
cles with radio and CD player> or multivision display
<vehicles with MMCS>, its respective connector(s),
the satellite radio tuner, the radio and CD player
<vehicles with radio and CD player> or the multivi-
sion display <vehicles with MMCS>.
.
PROBABLE CAUSES
• Malfunctions of satellite radio tuner
• Malfunctions of radio and CD player <vehicles
with radio and CD player> or multivision display
<vehicles with MMCS>
• Damaged harness wires and connectors
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB992006: Extra Fine Probe
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
Satellite Radio Tuner Communication Circuit <Vehicles with MMCS>
MULTIVISION
DISPLAY
SATELLITE RADIO TUNER
ACA02654
AI
Connectors: C-06, C-14, C-15, C-111
C-111
C-06 (G)
C-14,
C-15
SATELLITE RADIO TUNER
TSB Revision
CHASSIS ELECTRICAL
54A-678
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A
STEP1. Check whether AM or FM broadcast frequency is
received.
Check whether AM or FM broadcast frequency is received.
Q: Is AM or FM broadcast frequency received?
YES : Go to Step 2.
NO : Diagnose the radio and CD player <vehicles with
radio and CD player> or the multivision display
<vehicles with MMCS>. Refer to
<vehicles
with radio and CD player> or
<vehicles
with MMCS>.
STEP 2. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to GROUP 54A,
ETACS, Diagnosis, "How to connect the Scan Tool
(M.U.T.-III)
."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES <vehicles with radio and CD player> : Go to Step 3.
YES <vehicles with MMCS> : Go to Step 6.
NO <vehicles with radio and CD player or MMCS> :
Repair the CAN bus line. (Refer to GROUP 54C,
Diagnosis
).
STEP 3. Check satellite radio tuner connector C-111 and
radio and CD player connector C-14 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Is satellite radio tuner connector C-111 or radio and CD
player connector C-14 in good condition?
YES : Go to Step 4.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
SATELLITE RADIO TUNER
TSB Revision
CHASSIS ELECTRICAL
54A-679
STEP 4. Check the wiring harness between satellite radio
tuner connector C-111 (terminal 6, 14) and radio and CD
player connector C-14 (terminal 15, 6).
• Check the communication lines for open circuit and short
circuit.
Q: Is the wiring harness between satellite radio tuner
connector C-111 (terminal 6, 14) and radio and CD
player connector C-14 (terminal 15, 6) in good
condition?
YES : Go to Step 5.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary.
STEP5. Substitute a known good radio and CD player, and
check the trouble symptom.
Check whether satellite radio broadcast can be received.
Q: Can a satellite radio be received?
YES : Replace the radio and CD player.
NO : Replace the satellite radio tuner.
STEP 6. Check satellite radio tuner connector C-111 and
multivision display connector C-06 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Is satellite radio tuner connector C-111 or multivision
display connector C-06 in good condition?
YES : Go to Step 7.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
STEP 7. Check the wiring harness between satellite radio
tuner connector C-111 (terminal 6, 14) and multivision
display connector C-06 (terminal 85, 87).
• Check the communication lines for open circuit and short
circuit.
NOTE: Also check intermediate connector C-15 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector C-15 is damaged, repair or
replace the connector as described in GROUP 00E, Harness
Connector Inspection
.
Q: Is the wiring harness between satellite radio tuner
connector C-111 (terminal 6, 14) and multivision display
connector C-06 (terminal 85, 87) in good condition?
YES : Go to Step 8.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary.
SATELLITE RADIO TUNER
TSB Revision
CHASSIS ELECTRICAL
54A-680
STEP8. Substitute a known good multivision display, and
check the trouble symptom.
Check whether satellite radio broadcast can be received.
Q: Can a satellite radio be received?
YES : Replace the multivision display.
NO : Replace the satellite radio tuner.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст