Mitsubishi Outlander GS45X. Manual — part 510
ENGINE OIL PRESSURE SWITCH
TSB Revision
ENGINE LUBRICATION
12-9
ENGINE OIL PRESSURE SWITCH
REMOVAL AND INSTALLATION <2.4L ENGINE>
M1121002502045
Required Special Tool:
• MB992118: Oil Pressure Switch Wrench
REMOVAL SERVICE POINTS
.
<<A>> THROTTLE BODY MOUNTING BOLTS
REMOVAL
Remove the throttle body mounting bolts and put the throttle
body aside so as not to interfere the oil pressure switch con-
nector disconnection.
.
Pre-removal Operation
• Engine Room Under Cover Front A, B Removal (Refer to
GROUP 51, Under Cover
• Intake Manifold Stay Removal (Refer to GROUP 15,
Intake Manifold
).
Post-installation Operation
• Intake Manifold Stay Installation (Refer to GROUP 15,
Intake Manifold
).
• Engine Room Under Cover Front A, B Installation (Refer
to GROUP 51, Under Cover
AC506629 AE
1
2
10 ± 2 N·m
87 ± 17 in-lb
Removal steps
<<
A
>>
•
Throttle body mounting bolts (Refer
to Group 13A, Throttle Body
Assembly
)
1.
Engine oil pressure switch
connector connection
<<
B
>> >>
A
<< 2.
Engine oil pressure switch
Removal steps (Continued)
ENGINE OIL PRESSURE SWITCH
TSB Revision
ENGINE LUBRICATION
12-10
<<B>> ENGINE OIL PRESSURE SWITCH
REMOVAL
CAUTION
The sealant is applied to the bolt. Remove the bolt with
care not to break it.
Use special tool MB992118 to remove the engine oil pressure
switch.
INSTALLATION SERVICE POINT
.
>>A<< ENGINE OIL PRESSURE SWITCH INSTAL-
LATION
1. Apply sealant to the engine oil pressure switch thread.
Specified sealant: ThreeBond 1141J or equivalent
NOTE: Install the engine oil pressure switch immediately
after applying sealant.
CAUTION
After the installation, until a sufficient period of time (one
hour or more) elapses, do not apply the oil or water to the
sealant application area or start the engine.
2. In the same manner as removal, use special tool MD992118
to tighten the engine oil pressure switch to the specified
torque.
Tightening torque: 10
± 2 N⋅m (87 ± 17 in−lb)
AK502606 AD
MB992118
AK402699
1 mm
(0.04 in)
5 mm
(0.2 in)
AD
AK502606 AD
MB992118
ENGINE OIL PRESSURE SWITCH
TSB Revision
ENGINE LUBRICATION
12-11
REMOVAL AND INSTALLATION <3.0L ENGINE>
M1121002502056
Required Special Tool:
• MB992118: Oil Pressure Switch Wrench
REMOVAL SERVICE POINT
.
<<A>> ENGINE OIL PRESSURE SWITCH
REMOVAL
Use special tool MB992118 to remove the engine oil pressure
switch.
Pre-removal Operation
• Engine Room Under Cover Front Removal (Refer to
GROUP 51, Under Cover
Post-installation Operation
• Engine Room Under Cover Front Installation (Refer to
GROUP 51, Under Cover
AC705075 AE
2
3
1
10 ± 2 N·m
87 ± 17 in-lb
10 ± 2 N·m
87 ± 17 in-lb
Removal steps
1.
Engine oil pressure switch
connector connection
2.
Heat protector
<<
A
>> >>
A
<< 3.
Engine oil pressure switch
Removal steps (Continued)
AK502606 AD
MB992118
ENGINE OIL PRESSURE SWITCH
TSB Revision
ENGINE LUBRICATION
12-12
INSTALLATION SERVICE POINT
.
>>A<< ENGINE OIL PRESSURE SWITCH INSTAL-
LATION
1. Apply sealant to the engine oil pressure switch thread.
Specified sealant: ThreeBond 1141J or equivalent
NOTE: Install the engine oil pressure switch immediately
after applying sealant.
CAUTION
After the installation, until a sufficient period of time (one
hour or more) elapses, do not apply the oil or water to the
sealant application area or start the engine.
2. In the same manner as removal, use special tool MB992118
to tighten the engine oil pressure switch to the specified
torque.
Tightening torque: 10
± 2 N⋅m (87 ± 17 in−lb)
AK402699
1 mm
(0.04 in)
5 mm
(0.2 in)
AD
AK502606 AD
MB992118
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст