Mitsubishi Outlander GS45X. Manual — part 1538
TRAILING ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-21
Required Special Tool:
• MB990767: Front Hub and Flange Yoke Holder
AC802599
110 ± 11 N·m
81 ± 8 ft-lb
8.5 ± 1.5 N·m
76 ± 13 in-lb
11 ± 2 N·m
98 ± 17 in-lb
11 ± 2 N·m
98 ± 17 in-lb
71 ± 10 N·m
52 ± 7 ft-lb
39 ± 6 N·m
29 ± 4 ft-lb
90 ± 9 N·m
67 ± 6 ft-lb
N
<AWD>
144 176 N·m
107 129 ft-lb
*1
*1
*2
*2
*1
*2
*2
*2
*1
*1
*1
AC
95 ± 14 N·m
70 ± 10 ft-lb
N
58 ± 7 N·m
43 ± 5 ft-lb
*3
*2
71 ± 10 N·m
52 ± 7 ft-lb
*1
*1
145 ± 15 N·m
107 ± 11 ft-lb
11 ± 2 N·m
98 ± 17 in-lb
9
10
11
12
13
14
16
15
1
2
3
4
5
6
7
8
N
*3
Removal steps
1.
Cotter pin
<<
A
>> >>
B
<< 2.
Driveshaft nut
>>
B
<< 3.
Washer
4.
Rear wheel speed sensor
5.
Brake hose bracket
<<
B
>>
6.
Caliper assembly
7.
Brake disk
•
Driveshaft (Refer to Driveshaft
Removal and Installation
.)
8.
Rear wheel hub assembly
mounting bolt
<<
C
>>
9.
Rear wheel hub assembly
10. Parking brake cable mounting bolt
<<
D
>>
11. Rear brake assembly
12. Control link connection
13. Stabilizer link connection
<<
E
14. Lower arm assembly connection
15. Upper arm connection
16. Trailing arm assembly
Removal steps (Continued)
TRAILING ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-22
REMOVAL SERVICE POINTS
.
<<A>> DRIVESHAFT NUT REMOVAL
CAUTION
Do not apply the vehicle weight on the rear wheel hub
assembly with the driveshaft nut loosened. Otherwise, the
wheel bearing will be broken.
Use special tool MB990767 to fix the hub and remove the
driveshaft nut.
.
<<B>> CALIPER ASSEMBLY REMOVAL
1. Remove the caliper assembly with brake hose.
2. Secure the removed caliper assembly with a wire or other
similar material at a position where it will not interfere with
the removal and installation of the rear wheel hub assembly.
.
<<C>> REAR WHEEL HUB ASSEMBLY REMOVAL
Refer to GROUP 27B, Rear Axle Hub Assembly
.
<<D>> REAR BRAKE ASSEMBLY REMOVAL
Without separating the parking brake cable, hang the rear
brake assembly at the body-side using a string.
.
AC205988
MB990767
AB
AC700467AB
Rear
brake
assembly
Cord
Parking brake
cable
TRAILING ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-23
<<E>> LOWER ARM ASSEMBLY
DISCONNECTION
While jacking-up the lower arm with garage jack, remove the
mounting bolts.
INSTALLATION SERVICE POINTS
.
>>A<< REAR SENSOR COVER INSTALLATION
Align the marking with trailing arm hole as shown in the figure
and install the rear sensor cover.
.
AC608511AG
Garage
jack
Lower arm
assembly
AC700195AC
Marking
Rear sensor cover
Trailing arm
hole
TRAILING ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-24
>>B<< WASHER/DRIVESHAFT NUT
INSTALLATION
CAUTION
• Because the wheel speed detection magnetic encoder
is magnetized, it collects metallic particles easily. Make
sure that the magnetic encoder does not collect metal-
lic particles. Check that there is not any trouble prior to
reassembling it.
• When installing the drive shaft, make sure that it does
not contact with the wheel speed detection magnetic
encoder (integrated with the inner oil seal) to avoid
damage.
• Do not apply the vehicle weight on the rear wheel hub
assembly before fully tightening the driveshaft nuts.
Otherwise, the wheel bearing will be broken.
1. Incorporate the driveshaft washer as shown in the figure.
2. Use special tool MB990767 to tighten the driveshaft nuts. At
this time, tighten the nuts within the specified torque range
considering the final tightening.
Tightening torque: 144
− 176 N⋅m (107 − 129 ft-lb)
3. If the pin holes do not align with the pins, tighten the
driveshaft nut [less than 200 N
⋅m (147 ft-lb)] and find the
nearest hole then bend the cotter pin to fit it.
INSPECTION
M1341002300290
• Check the bushings for wear and deterioration.
• Check the trailing arm for bending or damage.
TRAILING ARM BUSHING REPLACEMENT <2.4L
ENGINE: 5 PERSONS SEAT>
M1341011300458
Required Special Tools:
• MB992121: Arm Bushing Remover and Installer
• MB992125: Arm Bushing Base
AC703571AB
Magnetic
encoder
Wheel
bearing
Rear hub
assembly
AC302292
AC505583
MB990767
AC
Washer
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст