Mitsubishi Outlander GS45X. Manual — part 1539
TRAILING ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-25
1. Use the special tools MB992121 and MB992125 to remove
the trailing arm bushing:
2. Determine the installation direction and the installation
position of the trailing arm bushing.
(1) Install so that the protruding side of the trailing arm
bushing inner pipe faces inside the body.
(2) Position horizontally the trailing arm bushing to body
connecting part, and locate bushing inner space as
shown in the figure.
AC506661AB
MB992121
MB992125
Trailing arm
Driving Out
AC612659AD
Bushing to body
connecting part
Bushing
inner space
TRAILING ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-26
3. Use the special tools MB992121 and MB992125 to press-fit
the trailing arm bushing up to the position shown in the
figure:
TRAILING ARM BUSHING REPLACEMENT <2.4L
ENGINE: 7PERSONS SEAT, 3.0L ENGINE>
M1341011300436
Required Special Tools:
• MB992121: Arm Bushing Remover and Installer
• MB992125: Arm Bushing Base
• MB992175: Base Spacer
1. Use the special tools MB992121 and MB992125 to remove
the trailing arm bushing.
AC506662 AB
MB992121
MB992125
Trailing arm
Press-fitting
AC608609
MB992121
MB992125
Driving Out
AC
Trailing arm
TRAILING ARM ASSEMBLY
TSB Revision
REAR SUSPENSION
34-27
2. Determine the installation direction and the installation
position of the trailing arm bushing.
(1) Install so that the protruding side of the trailing arm
bushing inner pipe faces inside the body.
(2) Position horizontally the trailing arm bushing to body
connecting part, and locate bushing inner space as
shown in the figure.
3. Use the special tools MB992121, MB992125 and
MB992175 to press-fit the trailing arm bushing up to the
position shown in the figure.
AC700250AC
Bushing to body
connecting part
Bushing
inner space
AC608611AC
MB992121
MB992125
Press-fitting
MB992175
Trailing arm
SHOCK ABSORBER ASSEMBLY
TSB Revision
REAR SUSPENSION
34-28
SHOCK ABSORBER ASSEMBLY
REMOVAL AND INSTALLATION
M1341002500863
CAUTION
• The parts indicated by
*1
should be temporarily tightened, and then fully tightened with the vehicle
standing on the ground and the curb weight condition.
• The parts indicated by
*2
are the bolts/nuts with friction coefficient stabilizer. In removal, ensure
there is no damage, clean dust and soiling from the bearing and thread surfaces, and tighten them
to the specified torque.
<2.4L Engine: 5 persons seat>
Pre-removal operation
• Quarter Trim Removal (Refer to GROUP 52A − Trim
Post-installation operation
• Using your fingers, press the Ball Joint Dust Cover to
check for a crack or damage.
• Quarter Trim Installation (Refer to GROUP 52A − Trim
AC606837AB
1
2
3
4
5
45 ± 7 N·m
33 ± 5 ft-lb
71 ± 10 N·m
52 ± 2 ft-lb
39 ± 6 N·m
29 ± 4 ft-lb
*2
*2
*2
*1
*1
71 ± 10 N·m
52 ± 2 ft-lb
*1
*1
Removal steps
1.
Stabilizer link connection
<<
A
>>
2.
Lower arm and trailing arm
connection
<<
A
>>
3.
Shock absorber and lower arm
connection
<<
B
>>
4.
Shock absorber mounting nut
>>
A
<< 5.
Shock absorber assembly
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст