Mitsubishi Outlander GS45X. Manual — part 541
TRANSAXLE MOUNTING
TSB Revision
POWER PLANT MOUNT
32-7
TRANSAXLE MOUNTING
REMOVAL AND INSTALLATION <2.4L ENGINE>
M1321001402049
Pre-removal operation
• Battery and Battery Tray Removal (Refer to GROUP 54A,
).
• Air Cleaner Assembly Removal (Refer to GROUP 15, Air
Cleaner
).
• Engine Control Module (ECM) Removal [Refer to GROUP
13A, Engine Control Module (ECM)
].
Post-installation operation
• Engine Control Module (ECM) Installation [Refer to
GROUP 13A, Engine Control Module (ECM)
].
• Air Cleaner Assembly Installation (Refer to GROUP 15,
Air Cleaner
).
• Battery and Battery Tray Installation (Refer to GROUP
54A, Battery
AC703854
1
2
2
3
AE
50 ± 5 N·m
37 ± 3 ft-ld
47 ± 7 N·m
35 ± 5 ft-ld
95 ± 10 N·m
71 ± 7 ft-lb
50 ± 5 N·m
37 ± 3 ft-ld
Removal steps
<<
A
>>
1.
Transaxle mounting bracket
•
Front roll stopper and
centermember assembly (Refer to
)
•
Transfer assembly <AWD> (Refer
to GROUP 23A, Transfer Assembly
>>
A
<< 2.
Transaxle mounting insulator
stopper
3.
Transaxle mounting insulator
Removal steps (Continued)
TRANSAXLE MOUNTING
TSB Revision
POWER PLANT MOUNT
32-8
REMOVAL SERVICE POINT
.
<<A>> TRANSAXLE MOUNTING BRACKET
REMOVAL
1. Place a garage jack against the transaxle case with a piece
of wood in between to support the engine and transaxle
assembly.
2. Operate a garage jack so that the transaxle weight is not
applied to the transaxle mounting insulator, and remove the
transaxle mounting bracket.
INSTALLATION SERVICE POINT
.
>>A<< TRANSAXLE MOUNTING INSULATOR
STOPPER INSTALLATION
Install the transaxle mounting insulator stopper as shown in the
figure.
AC505484
AC505484 AB
Engine side
Transaxle
mounting
insulator
Transaxle
mounting
insulator
stopper
TRANSAXLE MOUNTING
TSB Revision
POWER PLANT MOUNT
32-9
REMOVAL AND INSTALLATION <3.0L ENGINE>
M1321001402511
Pre-removal operation
• Battery and Battery Tray Removal (Refer to GROUP 54A,
).
• Air Cleaner Assembly Removal (Refer to GROUP 15, Air
Cleaner
).
• Engine Control Module (ECM) Removal [Refer to GROUP
13B, Engine Control Module (ECM)
].
Post-installation operation
• Engine Control Module (ECM) Installation [Refer to
GROUP 13B, Engine Control Module (ECM)
].
• Air Cleaner Assembly Installation (Refer to GROUP 15,
Air Cleaner
).
• Battery and Battery Tray Installation (Refer to GROUP
54A, Battery
AC702791
50 ± 5 N·m
37 ± 3 ft-ld
1
2
2
3
AC
50 ± 5 N·m
37 ± 3 ft-ld
47 ± 7 N·m
35 ± 5 ft-ld
95 ± 10 N·m
71 ± 7 ft-lb
Removal steps
<<
A
>>
1.
Transaxle mounting bracket
•
Front roll stopper and
centermember assembly (Refer to
•
Transfer assembly <AWD> (Refer
to GROUP 23C, Transfer Assembly
<Vehicles with
S-AWC>,
<Vehicles
without S-AWC>)
>>A<<
2.
Transaxle mounting insulator
stopper
3.
Transaxle mounting insulator
Removal steps (Continued)
TRANSAXLE MOUNTING
TSB Revision
POWER PLANT MOUNT
32-10
REMOVAL SERVICE POINT
.
<<A>> TRANSAXLE MOUNTING BRACKET
REMOVAL
1. Place a garage jack against the transaxle case with a piece
of wood in between to support the engine and V assembly.
2. Operate a garage jack so that the transaxle weight is not
applied to the transaxle mounting insulator, and remove the
transaxle mounting bracket.
INSTALLATION SERVICE POINT
.
>>A<< TRANSAXLE MOUNTING INSULATOR
STOPPER INSTALLATION
Install the transaxle mounting insulator stopper as shown in the
figure.
AC803110AB
Engine side
Transaxle mounting
insulator
Transaxle
mounting
insulator
stopper
Transaxle
mounting
bracket
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст