Mitsubishi Outlander GS45X. Manual — part 542

ENGINE ROLL STOPPER AND CENTERMEMBER

TSB Revision

POWER PLANT MOUNT

32-11

ENGINE ROLL STOPPER AND CENTERMEMBER

REMOVAL AND INSTALLATION

M1321002301644

CAUTION

• When the engine mounting insulator, transaxle mounting insulator and rear roll stopper have been

removed, tighten the engine mounting insulator, transaxle mounting insulator and rear roll stop-
per securely. Then, tighten the front roll stopper center nut *

1

securely.

• The parts indicated by the *2 are the bolts with friction coefficient stabilizer. In removal, ensure

there is no damage, clean dust and soiling from bearing and thread surfaces, and tighten them to

the specified torque.

Pre-removal and post-installation operation
• Engine Room Under Cover Front A<AWD>, B, and C Removal

and Installation (Refer to GROUP 51, Under Cover

P.51-23

).

<2.4L ENGINE>

• Engine Room Under Cover Front Removal and Installation (Refer

to GROUP 51, Under Cover

P.51-23

). <3.0L ENGINE>

AC702793

1

2

3

4

AD

50 ± 5 N·m
37 ± 3 ft-lb

50 ± 5 N·m
37 ± 3 ft-lb

1

2

<FWD>

<AWD>

2

1

2

2

53 ± 8 N·m
40 ± 5 ft-lb

71 ± 10 N·m*
52 ± 7 ft-lb*

56 ± 5 N·m*
41 ± 3 ft-lb*

71 ± 10 N·m*
52 ± 7 ft-lb*

4

Front roll stopper and
centermember removal steps

1.

Front roll stopper and
centermember assembly

2.

Centermember

>>A<<

3.

Front roll stopper

Rear roll stopper removal steps

•

Transfer assembly <AWD> (Refer to
GROUP 23A, Transfer Assembly

P.23A-163

) <CVT>, Refer to

GROUP 23C, Transfer Assembly

P.23C-292

<Vehicles with S-AWC>,

P.23C-293

<Vehicles without

S-AWC>) <A/T>.

4.

Rear roll stopper

ENGINE ROLL STOPPER AND CENTERMEMBER

TSB Revision

POWER PLANT MOUNT

32-12

INSTALLATION SERVICE POINT

.

>>A<< FRONT ROLL STOPPER INSTALLATION

Install the front roll stopper so that the hole faces toward the
vehicle front.

AC702794 AB

Hole

Front of vehicle

Front roll stopper

CROSSMEMBER

TSB Revision

POWER PLANT MOUNT

32-13

CROSSMEMBER

REMOVAL AND INSTALLATION <2.4L ENGINE>

M1321003201714

CAUTION

• Before replacing the steering wheel assembly and driver's air bag module assembly, always refer

to GROUP 52B, Service Precautions

P.52B-25

, and Air Bag Module(s) and Clock Spring

P.52B-439

.Also, position the front wheels in a straight ahead direction, and remove the ignition

key. If you fail to do this, clock spring for SRS may get damage, making the SRS (air bag) inopera-
tive, and it may cause a serious injury to the driver.

• The parts indicated by * are the bolts/nuts with friction coefficient stabilizer. In removal, ensure

there is no damage, clean dust and soiling from the bearing and thread surfaces, and tighten them
to the specified torque.

• After installation, perform calibration to make ASC-ECU learn the neutral position of the steering

wheel sensor. (Refer to GROUP 35C, On-vehicle Service

− Steering Wheel Sensor Calibration

P.35C-285

).

Pre-removal operation
• Steering Wheel and Air Bag Module Assembly Removal

(Refer to GROUP 37, Steering Wheel

P.37-32

).

• Footrest Removal.

• Front Roll Stopper and Centermember Assembly

Removal (Refer to

P.32-11

).

• Power Steering Fluid Drain (Refer to GROUP 37,

On-vehicle Service

− Fluid Replacement

P.37-25

).

• Engine Room Under Cover A<AWD>, B, C and Engine

Room Side Cover Removal (Refer to GROUP 51, Under

Cover

P.51-23

).

• Lower Arm Assembly Removal (Refer to GROUP 33,

Lower Arm

P.33-15

).

Post-installation operation
• Using Your Fingers, Press The Tie-rod End Ball Joint Dust

Cover To Check for a Crack or Damage (Refer to GROUP

37, On-vehicle Service

− Ball Joint Dust Cover Inspection

P.37-23

).

• Using Your Fingers, Press The Stabilizer Link Ball Joint

Dust Cover To Check for a Crack or Damage (Refer to

GROUP 33, On-vehicle Service

− Lower Arm Ball Joint

Dust Cover Inspection

P.33-9

).

• Lower Arm Assembly Installation (Refer to GROUP 33,

Lower Arm

P.33-15

).

• Front Roll Stopper and Centermember Assembly Installa-

tion (Refer to

P.32-11

).

• Engine Room Under Cover A<AWD>, B, C and Engine

Room Side Cover Installation (Refer to GROUP 51, Under

Cover

P.51-23

).

• Footrest Installation.

• Clock Spring Centering (Refer to GROUP 52B, Air Bag

Modules and Clock Spring

P.52B-439

).

• Steering Wheel Air Bag Module Assembly Installation

(Refer to GROUP 37, Steering Wheel

P.37-32

).

• Power Steering Fluid Refilling and Bleeding (Refer to

GROUP 37, On-vehicle Service

− Fluid Replacement

P.37-25

).

• Steering Wheel Straight-ahead Position Check.

• Front Wheel Alignment Check and Adjustment (Refer to

GROUP 33, On-vehicle Service

− Front Wheel Alignment

Check and Adjustment

P.33-7

).

CROSSMEMBER

TSB Revision

POWER PLANT MOUNT

32-14

Required Special Tool:

• MB991897 or MB992011: Ball Joint Remover

AC709740

<AWD>

<FWD>

1

AC

2

N

3

4

5

N

6

7

8

8

9

10

10

11

12

13

14

15

14

15

16

17

50 ± 5 N·m
37 ± 3 ft-lb

50 ± 5 N·m
37 ± 3 ft-lb

53 ± 8 N·m
40 ± 5 ft-lb

110 ± 11 N·m*
82 ± 8 ft-lb*

39 ± 6 N·m
29 ± 4 ft-lb

31 ± 4 N·m
23 ± 3 ft-lb

31 ± 4 N·m
23 ± 3 ft-lb

5.0 ± 2.0 N·m
45 ± 17 in-lb

70 ± 10 N·m
52 ± 7 ft-lb

20 ± 5 N·m
15 ± 3 ft-lb

39 ± 6 N·m
29 ± 4 ft-lb

25 ± 5 N·m
19 ± 3 ft-lb

57 ± 7 N·m
42 ± 5 ft-lb

13 ± 2 N·m
111 ± 22 in-lb

53 ± 8 N·m
40 ± 5 ft-lb

Removal steps

<<

A

>>

1.

Steering column shaft assembly
connection

<<

B

>>

2.

Self-lock nut (Tie-rod end and
knuckle connection)

3.

Stabilizer link assembly

4.

Eye bolt

5.

Gasket

6.

Pressure hose assembly

7.

Return hose connection

8.

Rear roll stopper center bolt

<<

C

>>

•

Front axle crossmember assembly

>>

B

<< 9.

Joint cover grommet

10. Rear roll stopper
11. Heat protector
12. Bracket
13. Steering gear and linkage assembly

>>

A

<< 14. Stabilizer bar bracket

>>

A

<< 15. Stabilizer bushing

>>

A

<< 16. Stabilizer bar

17. Front axle crossmember

Removal steps (Continued)