Mitsubishi Outlander GS45X. Manual — part 1644
DIAGNOSIS
TSB Revision
CVT
23A-133
OSCILLOSCOPE INSPECTION PROCEDURES
M1231208500209
With the connector remain connected, connect the
oscilloscope probe to each terminal of TCM.
43
Upshift switch
Transmission range:
Sport mode
Transmission range:
Upshift and hold
1 V or less
Transmission range:
Other than the above
Battery positive
voltage
44
Downshift switch
Transmission range:
Sport mode
Transmission range:
Downshift and hold
1 V or less
Transmission range:
Other than the above
Battery positive
voltage
45
Transmission range switch
D
• Ignition switch: ON
• Transmission range: D
Battery positive
voltage
• Ignition switch: ON
• Transmission range: other than D
1 V or less
48
Sensor ground
Always
1 V or less
49
Sensor power supply:
Ignition switch: ON
5.0 V
50
Transmission fluid
temperature sensor
• Ignition switch: ON
• Transmission fluid temperature: 20°C (68°F)
Approximately
2.0 V
• Ignition switch: ON
• Transmission fluid temperature: 80°C
(176
°F)
Approximately
1.0 V
51
Stepper motor C
Within 2 seconds after the ignition switch is
turned to the ON position
Pulse width: 30
ms
52
Stepper motor D
Within 2 seconds after the ignition switch is
turned to the ON position
Pulse width: 10
ms
Terminal
No.
Check item
Check condition
Standard value
Terminal
No.
Check item
Check condition
Normal
condition
Wave pattern
36 - 26
Secondary
pulley rotation
sensor
• Transmission
range: D
• Drive at a
constant speed
of
Approximately
20 km/h (12
mph)
Between 0 and
4.5 V, the pulse
cycle is
constant.
37 - 26
Primary pulley
rotation sensor
AC508912AB
(V)
(Time)
0
4.5
SPECIAL TOOL
TSB Revision
CVT
23A-134
SPECIAL TOOL
M1231200600600
Tool
Tool number and name Supersession
Application
MB991958
a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991914
f. MB991825
g. MB991826
M.U.T.-III sub assembly
a. Vehicle
communication
interface (V.C.I.)
b. M.U.T.-III USB cable
c. M.U.T.-III main
harness A (Vehicles
with CAN
communication
system)
d. M.U.T.-III main
harness B (Vehicles
without CAN
communication
system)
e. M.U.T.-III main
harness C (for
Chrysler models only)
f. M.U.T.-III
measurement adapter
g. M.U.T.-III trigger
harness
MB991824-KIT
NOTE: g:
MB991826
M.U.T.-III trigger
harness is not
necessary when
pushing V.C.I.
ENTER key.
CAUTION
For vehicles with CAN
communication, use the M.U.T.-III
main harness A to send the
simulated vehicle speed. If you
connect the M.U.T.-III main
harness B instead, the CAN
communication does not function
correctly.
CVT check (M.U.T.-III diagnostic
trouble code display and service
data display)
MB992006
Extra fine probe
−
Continuity check and voltage
measurement at harness wire or
connector
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
Do not use
a
b
c
d
e
f
g
Do not use
MB992006
SPECIAL TOOL
TSB Revision
CVT
23A-135
MD999576
Transmission range
switch adjusting gauge
−
Transmission range switch
adjustment
MD998330
a: MD998331
Oil pressure gauge (3.0
MPa)
a: Joint
MD998330-01
Hydraulic pressure measurement
MB992127
Joint
−
MB995062
Flushing tool
MLR-6906-C or
Equivalent
Flushing cooler and tube
Tool
Tool number and name Supersession
Application
AC103525A
a
SPECIAL TOOL
TSB Revision
CVT
23A-136
MB991454
Engine hanger balancer
MZ203827-01
Engine assembly support during
CVT assembly removal and
installation {For the engine hanger
balancer (MB991454), use chains
only.}
NOTE: Engine hanger balancer
(MB991454) is a part of the engine
hanger assembly (MB991453).
MB991527
Engine hanger
−
MB991928
Engine hanger
a: MB991929
Joint (50) x 2
b: MB991930
Joint (90) x 2
c: MB991931
Joint (140) x 2
d: MB991932
Foot (standard) x 4
e: MB991933
Foot (short) x 2
f: MB991934
Chain and fork
assembly
Tool not available
MB991895
Engine mechanical
hanger
Tool not available
MB991956
Engine hanger plate
−
Tool
Tool number and name Supersession
Application
B991454
B991527
B991928
a
b
c
d
e
f
Slide bracket (HI)
AI
Z203830
B991956
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст