Mitsubishi Outlander GS45X. Manual — part 220
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-877
REMOVAL AND INSTALLATION
M1547004900018
AC902749
1
AB
2
4
3
Removal Step
1.
Theft alarm sensor assembly
(Refer to GROUP 52A -
Headlining
2.
Theft alarm sensor
3.
Theft alarm sensor cover
4.
Sub harness
Removal Step (Continued)
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-878
REMOVAL AND INSTALLATION
M1547005000018
REMOVAL SERVICE POINT
.
<<A>> REMOVAL OF ANTENNA FEEDER
Remove the clip A and clip B.
AC901015
2
4
3
1
AE
11 ± 1 N·m
97 ± 8 in-ld
11 ± 1 N·m
97 ± 8 in-ld
18 ± 7 N·m
13 ± 5 ft-ld
Removal Steps
•
Strut tower bar (Refer to GROUP
33
− Strut assembly
•
ABS-ECU or ASC-ECU harness
connector (Refer to GROUP 35B
−
Hydraulic Unit
or
GROUP 35C- Hydraulic Unit
<<A>>
1.
Theft alarm siren assembly
2.
Theft alarm siren bracket
3.
Theft alarm siren
4.
Sub harness
Removal Steps (Continued)
AC902111
Clip A
Clip B
AB
THEFT ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-879
INSPECTION
LIN CUTOFF CONTROL UNIT CHECK
M1547005600010
.
CONTINUITY CHECK
Remove the LIN cutoff control unit.(Refer to
)
.
RELAY CHECK
Remove the LIN cutoff control unit.(Refer to
)
THEFT-ALARM INDICATOR CHECK
M1547001100198
1. Remove the center panel.
2. Connect the battery (+) terminal with the center panel
connector (terminal No. 15). Then, check if the theft-alarm
indicator is illuminated when the battery (
−) terminal and the
center panel connector (terminal No. 12) are connected.
3. If the theft-alarm indicator is illuminated, it is judged good.
Terminal number
Measurement value
5 to 3
Continuity exists (2
Ω or
less)
Battery voltage
Terminal
number
Normal
condition
At no energization
5 to 7
No
continuity
With current supply
[terminal 1 (+), terminal 8
(
−)]
Continuity
exists (2
Ω
or less)
AC900636AB
AC703574 AB
Center panel
PANIC ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-880
PANIC ALARM
GENERAL INFORMATION
M1547000100311
If danger is perceived near the vehicle and if the igni-
tion switch is in the OFF position or the key has been
removed, press the panic button on the ignition key
or the keyless operation key for one second, then the
headlights flash and the horns(HI, LO, theft-alarm
horn <Vehicles without theft-alarm siren>) sound for
approximately 3 minutes.
NOTE: The theft-alarm siren does not sound.<Vehi-
cles with theft-alarm siren>
Panic alarm system operation table
Construction diagram
.
Operation of keyless operation key or ignition key
System operation
Panic button
Press once (press and hold
for 1 second)
Starts the panic alarm (headlights flash and horn
honks for abut three minutes)
Lock button, Unlock button,
Panic button
Press again
Stops the panic alarm in progress
AC901213
Panic button
Panic button
<Vehicles with KOS>
<Vehicles with WCM>
Theft-alarm horn
<Vehicles without theft-alarm siren>
Horn (LO)
Horn (HI)
Headlight
ETACS-ECU
PANIC
AB
Headlight
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст