Mitsubishi Outlander GS45X. Manual — part 1485
FRONT IMPACT SENSORS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-435
2. Position the front impact sensor facing toward the front of
the vehicle as indicated by the arrow on the label, and install
it securely.
.
>>C<< POST-INSTALLATION INSPECTION
1. Reconnect the negative (
−) battery cable.
2. Turn the ignition key to "ON" position.
3. Does the "SRS" warning light illuminate for approximately
seven seconds, and then remain off for at least five seconds
after turning "OFF"?
4. If yes, the SRS system is functioning properly.
If not, consult page
.
INSPECTION
M1524001600716
WARNING
If a dent, crack, deformation or rust is
detected, replace with a new sensor.
NOTE: For checking of the front impact sensor other
than described below, refer to the section concerning
SRS diagnosis (Refer to
1. Check the front impact sensor and bracket for
dents, cracks or deformation.
2. Check the connector for damage, and terminals
for deformation.
3. Check that there is no bending or corrosion in the
radiator support panel.
AC901647
SRS Warning light
AB
SRS CONTROL UNIT (SRS-ECU)
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-436
SRS CONTROL UNIT (SRS-ECU)
REMOVAL AND INSTALLATION
M1524002101610
DANGER
The SRS-ECU adopts the rollover specification that the curtain air bag and seat belt pre-ten-
sioner operate at the occurrence of rollover. Therefore, do not tilt the vehicle to the right and
left with the IG ON or tilt the SRS-ECU to the right and left with the IG ON and the harness
installed.
WARNING
•
Never attempt to disassemble or repair the SRS-ECU. If faulty, replace it.
•
Do not drop or subject the SRS-ECU to impact or vibration. If denting, cracking, deforma-
tion, or rust are discovered in the SRS-ECU, replace it with a new SRS-ECU.
•
After deployment of an air bag, replace the SRS-ECU with a new one.
•
Never use an ohmmeter on or near the SRS-ECU, and use only the special test equipment
described here
.
Pre-removal Operation
• Turn the ignition switch to the "LOCK" (OFF) position.
AC701943
1
AC
4
3
2
9.0 ± 1.0 N·m
80 ± 8 in-lb
9.0 ± 1.0 N·m
80 ± 8 in-lb
Removal steps
<<A>>
1.
Negative (
−) battery cable
connection
•
Lower side cover (Refer to GROUP
52A
− Front Floor Console
).
2.
SRS-ECU mounting bolt (ground
bolt)
3.
SRS-ECU mounting bolt
<<B>>
4.
SRS-ECU
Installation steps
>>A<<
4.
SRS-ECU
3.
SRS-ECU mounting bolt
>>B<<
2.
SRS-ECU mounting bolt (ground
bolt)
•
Lower side cover (Refer to GROUP
52A
− Front Floor Console
1.
Negative (
−) battery cable
connection
>>C<<
•
Post-installation inspection
SRS CONTROL UNIT (SRS-ECU)
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-437
REMOVAL SERVICE POINTS
.
<<A>> NEGATIVE (
−) BATTERY CABLE DISCON-
NECTION
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cable before doing any further work (Refer to
).
WARNING
Battery posts, terminals and related accessories con-
tain lead and lead compounds. WASH HANDS AFTER
HANDLING.
Disconnect the negative battery cable from the battery and tape
the terminal to prevent accidental connection and deployment.
.
<<B>> SRS-ECU REMOVAL
DANGER
The SRS-ECU adopts the rollover specification that
the curtain air bag and seat belt pre-tensioner operate
at the occurrence of rollover. Therefore, do not tilt the
vehicle to the right and left with the IG ON or tilt the
SRS-ECU to the right and left with the IG ON and the
harness installed.
While pushing the part "A" indicated in the figure of the harness
side connector, turn the lock lever to the direction of the arrow
to release the lock lever.
INSTALLATION SERVICE POINTS
.
>>A << SRS-ECU INSTALLATION
WARNING
The SRS may not activate if the SRS-ECU is not
installed properly, which could result in serious injury
or death to the vehicle's driver or front passenger.
.
ACX00583
Insulating tape
Battery cable
Battery
AF
AC506734
A
AB
Lock lever
SRS CONTROL UNIT (SRS-ECU)
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-438
>>B<< SRS-ECU MOUNTING BOLT (GROUND
BOLT) INSTALLATION
Check the head mark "E" and install the ground bolt.
.
>>C<< POST-INSTALLATION INSPECTION
1. Reconnect the negative (
−) battery cable.
2. Turn the ignition switch to the "ON" position.
3. Does the "SRS" warning light illuminate for approximately
seven seconds, and then go out?
4. If yes, the SRS system is functioning properly. If not, refer to
.
INSPECTION
M1524002200670
WARNING
If a dent, crack, deformation or rust is dis-
covered, replace the SRS-ECU with a new
one.
• Check the SRS-ECU and brackets for dents,
cracks or deformation.
• Check the SRS-ECU connector for damage, and
the terminals for deformation.
NOTE: Refer to
for other than physical damage.
AC105754 AB
Earth bolt head mark
AC901647
SRS Warning light
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст