Mitsubishi Outlander GS45X. Manual — part 520
INTAKE MANIFOLD PLENUM <3.0L ENGINE>
TSB Revision
INTAKE AND EXHAUST
15-7
AC809105AB
19
18
17
16
15
14
13
12
20
21
N
N
N
11 ± 1 N·m
97 ± 8 in-lb
23 ± 6 N·m
17 ± 4 ft-lb
22 ± 1 N·m
16 ± 1 ft-lb
22 ± 1 N·m
16 ± 1 ft-lb
23 ± 6 N·m
17 ± 4 ft-lb
11 ± 1 N·m
97 ± 8 in-lb
11 ± 1 N·m
97 ± 8 in-lb
11 ± 1 N·m
97 ± 8 in-lb
23 ± 6 N·m
17 ± 4 ft-lb
23 ± 6 N·m
17 ± 4 ft-lb
23 ± 6 N·m
17 ± 4 ft-lb
23 ± 6 N·m
17 ± 4 ft-lb
11 ± 1 N·m
97 ± 8 in-lb
22 ± 1 N·m
16 ± 1 ft-lb
Removal steps
12. PCV hose connection
13. Brake booster vacuum hose
connection
14. Throttle body stay
15. Intake manifold plenum stay (rear)
16. Intake manifold plenum stay (front)
17. EGR pipe
18. EGR pipe gasket
19. EGR pipe gasket
20. Intake manifold plenum
21. Intake manifold plenum gasket
Removal steps (Continued)
INTAKE MANIFOLD PLENUM <3.0L ENGINE>
TSB Revision
INTAKE AND EXHAUST
15-8
INSTALLATION SERVICE POINT
.
>>A<< MANIFOLD ABSOLUTE PRESSURE SEN-
SOR INSTALLATION
CAUTION
• Install the manifold absolute pressure sensor, taking
care not to give a shock to it.
• Do not use a manifold absolute pressure sensor that
has fallen down.
INTAKE MANIFOLD
TSB Revision
INTAKE AND EXHAUST
15-9
INTAKE MANIFOLD
REMOVAL AND INSTALLATION <2.4L ENGINE>
M1151003004570
Pre-removal operation
• Engine Coolant Draining (Refer to GROUP 14, On-vehicle
Service
− Engine Coolant Change
• Engine Upper Cover Removal (Refer to GROUP 11A,
Camshaft
• Generator and Others Belt Removal (Refer to GROUP
11A, Crankshaft Pulley
).
• Air Cleaner Intake Hose and Air Cleaner Assembly
Removal (Refer to
).
• Throttle Body Assembly Removal (Refer to GROUP 13A,
Throttle Body Assembly
).
• Fuel Injector Removal (Refer to GROUP 13A, Injector
).
• EGR Valve and EGR Valve Stay Removal (Refer to
GROUP 17, EGR Valve
Post-installation operation
• EGR Valve and EGR Valve Stay Installation (Refer to
GROUP 17, EGR Valve
• Fuel Injector Installation (Refer to GROUP 13A, Injector
).
• Throttle Body Assembly Installation (Refer to GROUP
• Air Cleaner Intake Hose and Air Cleaner Assembly Instal-
lation (Refer to
).
• Generator and Others Belt Installation (Refer to GROUP
11A, Crankshaft Pulley
).
• Engine Upper Cover Installation (Refer to GROUP 11A,
Camshaft
).
• Engine Coolant Refilling (Refer to GROUP 14, On-vehicle
Service
− Engine Coolant Change
).
AC606245AD
1
2
3
4
5
8
9
11
7
6
N
10
10
N
12
14
15
15
15
16
17
18
N
13
N
16
Apply new engine oil
to the O-ring before
installation.
3.5 ± 1.5 N·m
31 ± 13 in-lb
to
20 ± 2 N·m
15 ± 1 ft-lb
4.0 ± 1.0 N·m
36 ± 8 in-lb
4.0 ± 1.0 N·m
36 ± 8 in-lb
20 ± 2 N·m
15 ± 1 ft-lb
3.5 ± 1.5 N·m
31 ± 13 in-lb
to
20 ± 2 N·m
15 ± 1 ft-lb
25 ± 4 N·m
18 ± 3 ft-lb
N
10
INTAKE MANIFOLD
TSB Revision
INTAKE AND EXHAUST
15-10
REMOVAL SERVICE POINT
.
<<A>> POWER STEERING OIL PUMP ASSEMBLY
REMOVAL
1. With the hose installed, remove the power steering oil pump
assembly from the bracket.
2. Tie the removed power steering oil pump assembly with a
string at a position where it will not interfere with the removal
and installation of the intake manifold.
INSTALLATION SERVICE POINTS
.
>>A<< SCREW INSTALLATION
CAUTION
Do not over-tighten. As the self-forming-type screw is
used, the excessive torque can damage the intake mani-
fold threads.
.
>>B<< MANIFOLD ABSOLUTE PRESSURE
SENSOR INSTALLATION
CAUTION
• Install the manifold absolute pressure sensor, taking
care not to give a shock to it.
• Do not use a manifold absolute pressure sensor that
has fallen down.
.
>>C<< INTAKE MANIFOLD ASSEMBLY/INJECTOR
PROTECTOR FRONT INSTALLATION
Install the intake manifold assembly and the injector protector
front, and tighten mounting bolts and nuts temporarily.
NOTE: The tightening of the fuel rail, the intake manifold
assembly and the injector protector front and rear has the spec-
ified order. Temporarily tighten the intake manifold assembly
and injector protector front mounting bolts and nuts (Refer to
GROUP 13A, Injector
).
Removal steps
1.
Control wiring harness connection
2.
Emission vacuum hose
3.
Brake booster vacuum hose
<<
A
>>
4.
Power steering oil pump assembly
5.
Rocker cover PCV hose
6.
Engine oil level gauge
7.
Intake manifold stay
>>
C
<< 8.
Injector protector front
>>
C
<< 9.
Intake manifold assembly
10. Intake manifold gasket
>>
A
<< 11. Screw
>>
B
<< 12. Manifold absolute pressure sensor
13. O-ring
>>
A
<< 14. Screw
15. Purge control solenoid valve
16. O-ring
17. Intake manifold harness bracket
18. Engine cover bracket
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст