Mitsubishi Outlander GS45X. Manual — part 942
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-701
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• 2 seconds or more have passed since the engine
starting sequence was completed.
• Battery positive voltage is higher than 6 volts.
Judgement Criterion
• Barometric pressure sensor output signal has
continued to be 49 kPa (14.5 in.Hg) or lower
(approximately 15,000 feet above sea level) for
10 seconds.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Pattern 22
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are:)
• ECM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
AK604366
Good
Malfunction
End
No
No
No
No
Barometric Pressure
< 49kPa (14.5 in. Hg)
Barometric Pressure
> 113kPa (33.4 in. Hg)
Start
Yes
Yes
Yes
Yes
Continuous
failure for 10secs
Monitoring
conditions
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-702
STEP 1. Test the OBD-II drive cycle.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Carry out the test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Pattern 22
(4) Check the diagnosis trouble code (DTC).
Q: Is DTC P02228 set?
YES : Replace the ECM. When the ECM is replaced,
register the ID code. Refer to GROUP 42B, Diagnosis
− ID Codes Registration Judgment Table <Vehicles
or GROUP 42C, Diagnosis
− ID
Codes Registration Judgment Table <Vehicles with
WCM>
NO : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
DTC P2229: Barometric Pressure Circuit High Input
.
TECHNICAL DESCRIPTION
• The barometric pressure sensor outputs a volt-
age which corresponds to the barometric pres-
sure.
• The ECM checks whether this voltage is within a
specified range.
.
DESCRIPTIONS OF MONITOR METHODS
Barometric pressure sensor output voltage is out of
reasonable barometric pressure range.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS
(Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
AK700568AB
MB991824
MB991827
MB991910
Data link
connector
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-703
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• 2 seconds or more have passed since the engine
starting sequence was completed.
• Battery positive voltage is higher than 6 volts.
Judgement Criterion
• Barometric pressure sensor output signal has
continued to be 113 kPa (33.4 in.Hg) or higher
(approximately 4,000 ft below sea level) for 10
seconds.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Pattern 22
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are:)
• ECM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
AK604366
Good
Malfunction
End
No
No
No
No
Barometric Pressure
< 49kPa (14.5 in. Hg)
Barometric Pressure
> 113kPa (33.4 in. Hg)
Start
Yes
Yes
Yes
Yes
Continuous
failure for 10secs
Monitoring
conditions
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-704
STEP 1. Test the OBD-II drive cycle.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Carry out the test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Pattern 22
(4) Check the diagnosis trouble code (DTC).
Q: Is DTC P02229 set?
YES : Replace the ECM. When the ECM is replaced,
register the ID code. Refer to GROUP 42B, Diagnosis
− ID Codes Registration Judgment Table <Vehicles
or GROUP 42C, Diagnosis
− ID
Codes Registration Judgment Table <Vehicles with
WCM>
NO : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
DTC P2252: Heated Oxygen Sensor Offset Circuit Low Voltage
AK700568AB
MB991824
MB991827
MB991910
Data link
connector
AK900130AD
Right bank heated
oxygen sensor (rear)
Front exhaust
pipe RH
B-02 (B)
Connector: B-02
AK900129 AD
Right bank heated
oxygen sensor (front)
Front exhaust
pipe RH
B-03 (GR)
Connector: B-03
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст