Mitsubishi Outlander GS45X. Manual — part 53
HEADLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-209
HEADLIGHT BULB (HIGH-BEAM) REPLACEMENT
<VEHICLES WITHOUT DISCHARGE HEADLIGHT>
CAUTION
Do not touch the bulb surface with bare hands or dirty
gloves. If the bulb surface (glass part) gets dirty, immedi-
ately clean it with alcohol or thinner. After drying com-
pletely, install the bulb.
1. Twist the socket cover to remove.
2. Disconnect the connector, and twist the headlight bulb
(high-beam) to remove.
DAYTIME RUNNING LIGHT BULB REPLACEMENT
<VEHICLES WITH DISCHARGE HEADLIGHT>
CAUTION
Do not touch the bulb surface with bare hands or dirty
gloves. If the bulb surface (glass part) gets dirty, immedi-
ately clean it with alcohol or thinner. After drying com-
pletely, install the bulb.
1. Twist the socket cover to remove.
2. Twist the daytime running light socket to remove it.
POSITION LIGHT BULB REPLACEMENT
Disconnect the connector, and twist the position light socket to
remove it.
AC901181
AC
Socket cover (High-beam)
AC900447AC
Socket cover
(Daytime running light bulb)
AC901181
AD
Position light
HEADLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-210
FRONT TURN-SIGNAL LIGHT BULB
REPLACEMENT
Disconnect the connector, and twist the front turn-signal light
socket to remove it.
HEADLIGHT AUTOMATIC-SHUTDOWN
FUNCTION CHECK
M1540100800167
Confirm that the headlights turn OFF in one second if the igni-
tion key is pulled out and the driver's door is opened when the
ignition switch is ON and the lighting switch is ON (HEAD posi-
tion). If there is a malfunction, perform the troubleshooting
(Refer to
HEADLIGHT AUTO LIGHT FUNCTION CHECK
M1540100900238
Under the direct sunlight with the ignition switch ON and the
lighting switch in the AUTO position, check that the headlight
automatically illuminates when the lighting control sensor
receiver is covered by hand. If there is any trouble, carry out
the troubleshooting. (Refer to
.)
NOTE: When covering the lighting control sensor receiver, be
careful not to touch the windshield surface (where the lighting
control sensor receiver is mounted). (The lighting control sen-
sor receiver has limited resistance to oil.)
CUSTOMIZATION FUNCTION
M1540103700783
With the scan tool MB991958 operation, the follow-
ing functions can be programmed. The programmed
information is held even when the battery is discon-
nected.
AC901181
AE
Front turn-signal light
Adjustment
item (scan tool
display)
Adjustment item
Adjustment contents
(scan tool display)
Adjusting contents
Turn power
source
Adjustment of
turn-signal light
operation condition
ACC or IG1
Operable with ACC or ON position
IG1
Operable with ON position (initial
condition)
Comfort flasher With/without
comfort flasher
function
Disable
Without function
Enable
With function (initial condition)
HEADLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-211
Comfort flasher
switch time
Switch operation
time to activate the
comfort flasher
function
Normal
0.4 second (initial condition)
Long
0.8 second
Hazard answer
back
Adjustment of the
number of keyless
hazard warning light
answer back
flashes
Lock:1, Unlock:2
LOCK: Flashes once, UNLOCK: Flashes
twice (initial condition)
Lock:1, Unlock:0
LOCK: Flashes once, UNLOCK: No flash
Lock:0, Unlock:2
LOCK: No flash, UNLOCK: Flash twice
Lock:2, Unlock:1
LOCK: Flash twice, UNLOCK: Flash once
Lock:2, Unlock:0
LOCK: Flash twice, UNLOCK: No flash
Lock:0, Unlock:1
LOCK: No flash, UNLOCK: Flash once
Lock:0, Unlock:0
Without function
Sensitivity for
auto light
Lighting control
sensor sensitivity
(illumination
intensity) <vehicles
with auto light>
Level 1 bright
High-high ambient brightness
Level 2 bright
High ambient brightness
Level 3
Standard ambient brightness (initial
condition)
Level 4 dark
Low ambient brightness
Level 5 dark
Low-low ambient brightness
Headlight auto
cut customize
Adjustment of
headlight automatic
shutdown function
Disable
Without function
Enable (C-spec.).
With function (initial condition)
Welcome light
Disabling or
enabling welcome
light function
Disabled
No function
Small light
Tail light illuminates. (initial condition)
Head light
Headlight illuminates.
Coming home
light
Disabling or
enabling coming
home light function
Disabled
No function
15 sec
Headlight illuminates for 15 seconds.
30sec
Headlight illuminates for 30 seconds.
(initial condition)
60 sec
Headlight illuminates for 60 seconds.
180 sec
Headlight illuminates for 180 seconds.
Adjustment
item (scan tool
display)
Adjustment item
Adjustment contents
(scan tool display)
Adjusting contents
HEADLIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-212
HEADLIGHT REMOVAL AND INSTALLATION
M1540101000744
<VEHICLES WITHOUT DISCHARGE HEADLIGHT>
Pre-removal operation
Front bumper assembly removal (Refer to GROUP 51
−
Front Bumper Assembly
Post-installation operation
• Front bumper assembly installation (Refer to GROUP 51
− Front Bumper Assembly
• Check the beam direction of the headlight (Refer to Head-
AC900661AC
5
1
2
6
3
4
7
Section A - A
1
A
A
7
1.5 ± 0.3 N·m
14 ± 2 in-lb
4.5 ± 1.5 N·m
40 ± 13 in-lb
4.5 ± 1.5 N·m
40 ± 13 in-lb
4.5 ± 1.5 N·m
40 ± 13 in-lb
Removal Steps
1.
Headlight assembly
2.
Headlight bulb (low-beam)
3.
Headlight bulb (high-beam)
4.
Front turn-signal light bulb
5.
Position light bulb
6.
Grommet
7.
Grommet
Removal Steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст