Mitsubishi Outlander GS45X. Manual — part 1078
DOOR
TSB Revision
BODY
42A-115
STEP 26. Check ETACS-ECU connector C-311 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is ETACS-ECU connector C-311 in good condition?
YES : Go to Step 27.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. When the rear power window sub switch
(RH) is operated, the rear power window (RH) should
raise and lower normally.
STEP 27. Check the wiring harness between ETACS-ECU
connector C-311 (terminal 12) and rear power window sub
switch (RH) connector E-11 (terminal 6).
• Check the power supply line for open circuit and short cir-
cuit.
NOTE: Also check intermediate connectors D-36. If intermedi-
ate connector D-36 is damaged, repair or replace the connector
as described in GROUP 00E, Harness Connector Inspection
Q: Is the wiring harness between ETACS-ECU connector
C-311 (terminal 12) and rear power window sub switch
(RH) connector E-11 (terminal 6) in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. When the
rear power window sub switch (RH) is operated, the
rear power window (RH) should raise and lower
normally.
STEP 28. Check the ground circuit to the rear power
window sub switch (RH). Measure the resistance at rear
power window sub switch (RH) connector E-11.
(1) Disconnect rear power window sub switch (RH) connector
E-11 and measure the resistance available at the wiring
harness side of the connector.
(2) Measure the resistance value between terminal 5 and
ground, and also between terminal 8 and ground.
• The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 30.
NO : Go to Step 29.
AC702473AJ
Connector E-11
(harness side)
DOOR
TSB Revision
BODY
42A-116
STEP 29. Check the wiring harness between power
window main switch connector E-19 (terminals 15, 17) and
rear power window sub switch (RH) connector E-11
(terminals 5, 8).
• Check the power supply lines for open circuit and short cir-
cuit.
NOTE: Also check intermediate connectors C-20, C-126 and
D-36. If intermediate connector C-20, C-126 or D-36 is dam-
aged, repair or replace the damaged component(s) as
described in GROUP 00E, Harness Connector Inspection
Q: Is the wiring harness between power window main
switch connector E-19 (terminals 15, 17) and rear power
window sub switch (RH) connector E-11 (terminals 5, 8)
in good condition?
YES : Replace the power window main switch. When the
rear power window sub switch (RH) is operated, the
rear power window (RH) should raise and lower
normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. When the
rear power window sub switch (RH) is operated, the
rear power window (RH) should raise and lower
normally.
STEP 30. Check the wiring harness between rear power
window sub switch (RH) connector E-11 (terminals 4, 7)
and rear power window motor (RH) connector E-12
(terminals 4, 1).
• Check the power supply lines for open circuit and short cir-
cuit.
Q: Is the wiring harness between rear power window sub
switch (RH) connector E-11 (terminals 4, 7) and rear
power window motor (RH) connector E-12 (terminals 4,
1) in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. When the
rear power window sub switch (RH) is operated, the
rear power window (RH) should raise and lower
normally.
DOOR
TSB Revision
BODY
42A-117
INSPECTION PROCEDURE C-4: Front and/or Rear Passenger's Power Window(s) do not work by
means of the Power Window Main Switch.
CAUTION
Before replacing the ECU, ensure that the power
supply circuit, the ground circuit and the com-
munication circuit are normal.
ACA01306AC
Power window (Front Passenger's side) Circuit
BLA
CK
BLA
CK
BLA
CK
BLA
CK
RED
RED
GREEN
GREEN
BLUE-
WHITE
BLUE-
WHITE
WHITE-
BLA
CK
GREEN
FRONT
(RH)
LOCK
SWITCH
POWER
WINDOW
MAIN SWITCH
VIOLET
BLUE
FRONT
POWER
WINDOW
SUB
SWITCH
FRONT
POWER
WINDOW
MOTOR (RH)
ETACS-ECU
POWER
WINDOW
RELAY
E-19
C-126
C-112
E-06
E-03
DOOR
TSB Revision
BODY
42A-118
ACA01307
BLA
CK
REAR
(LH)
REAR
(RH)
LOCK
SWITCH
POWER WINDOW MAIN SWITCH
BLA
CK
BLA
CK
BLA
CK
RED
RED
BR
O
W
N
BR
O
W
N
BR
O
W
N
BR
O
W
N
YELLO
W
YELLO
W
YELLO
W
YELLO
W
GRA
Y
YELLO
W
GRA
Y
GRA
Y
GRA
Y
BLUE
BLUE
BLUE
BLUE
WHITE
WHITE
WHITE
WHITE
REAR
POWER
WINDOW
SUB SWITCH
(LH)
REAR
POWER
WINDOW
MOTOR (LH)
REAR
POWER
WINDOW
SUB SWITCH
(RH)
REAR
POWER
WINDOW
MOTOR (RH)
AC
Power window (Rear Door) Circuit
BLUE-WHITE
ETACS-ECU
POWER
WINDOW
RELAY
E-19
C-20
D-36
C-32
D-21
C-126
E-11
E-12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст